Synthetic

TRIM 9106 is a clear, virtually odorless, synthetic coolant with excellent heat dissipating and corrosion inhibiting qualities. Recommended for grinding operations on cast iron, aluminum, and steels. Will not form ammonia when grinding cast iron and allows graphite to float and prevents swarf from clinkering when grinding cast iron. Contains no sulfur, phosphorus, chlorine, or other halogens.

Low mist

Low foam

Moderate pH

Very low odor

Clear working solution

Very operator, machine, and environmentally friendly

Will not form ammonia or other gases when grinding or machining cast iron

Inhibits chip packing and clinkering

Compatible with brass, aluminum, and lead serrations on magnetic grinding chucks

Machines are easily washed off with coolant working solution to minimize the buildup of residues and chips

Very low carryoff for extremely low fluid operating costs

Easy recycling or disposal with conventional techniques and equipment

Synthetic

TRIM C115 is a high-performance, synthetic fluid for working cast iron and mild steels. State-of-the-art chemical technology provides excellent cooling and chip settling, good tramp oil rejection, and machine cleanliness while leaving a protective film on the machine tool.

Does an excellent job in most glass, ceramic, and composite grinding applications

Excellent corrosion inhibition on most common ferrous and nonferrous alloys

Extremely low carryoff keeps operating costs down

Low foam and mist

Very low initial odor level which usually disappears after one-to-two days

Keeps your machines clean while leaving a soft, fluid film that protects bare metal parts

Exceptional sump life and very good tramp oil rejection

High-performance Synthetic

TRIM C270 is a state-of-the-art synthetic coolant. C270 provides excellent cooling and chip settling, good tramp oil rejection, and machine cleanliness, and meets the need of the modern job shop for a single premium synthetic coolant for virtually all machining operations.

C270 is compatible with a very wide range of materials including: cast iron, steels, and copper alloys, as well as plastics and composites

Provides excellent corrosion inhibition on all common ferrous alloys

Does a great job in form grinding, drilling, tapping, and reaming operations without chlorine or sulfur-based EP additives

Extremely low carryoff for very low total operation costs

Very low foam and mist

Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts. This residual film is easily resoluble in coolant working solution to facilitate easy machine cleaning and minimize the buildup of sticky residues that can hold machine-destroying chips

Exceptional sump life and very good tramp oil rejection

A very low initial odor level which usually disappears after one-to-two days

High-performance Synthetic

TRIM C270CG is a state-of-the-art synthetic coolant. C270CG provides excellent cooling and chip settling, good tramp oil rejection and machine cleanliness and meets the need of the modern job shop for a single premium synthetic coolant for virtually all machining operations.

Provides excellent corrosion inhibition on all common ferrous alloys

Does a great job in form grinding, drilling, tapping, and reaming operations without chlorine or sulfur-based EP additives

Extremely low carryoff for very low total operation costs

Very low foam and mist

Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts. This residual film is easily resoluble in coolant working solution to facilitate easy machine cleaning and minimize the buildup of sticky residues that can hold machine-destroying chips

Exceptional sump life and very good tramp oil rejection

A very low initial odor which usually disappears after one to two days

Clean-running Synthetic

TRIM C276 is a synthetic coolant that meets the needs of the most modern and demanding manufacturers. C276 makes use of the latest synthetic coolant formulation and specially synthesized oil to produce a versatile product that is clean running, has great sump life, and is kind to both machines and operators. This product will perform well in centerless and cylindrical form grinding as well as on high-speed, single-point turning, and down-the-hole work on vertical and horizontal machining centers.

Very low foam and mist

Provides excellent corrosion inhibition on all common ferrous alloys

Keeps your machines clean while leaving a soft fluid film that protects the bare metal parts of your machine tools - this film is easily washed off with coolant working solution for easy machine cleaning

Excellent extreme pressure (EP) lubricity to do many form grinding, drilling, and tapping operations

Extremely low carryoff for very low total operation costs

Exceptional sump life and very good tramp oil rejection

Low initial charge odor which dissipates further after one or two days

Minimizes the buildup of sticky residues

General-purpose Synthetic for Aluminum

TRIM C290 is a synthetic metalworking fluid optimized for the chemical, environmental, and machining requirements of general aluminum parts. C290 is a high performance, easy to use and maintain, metal removal fluid with very high levels of usable lubricity at the point-of-cut. C290's unique chemical formula allows great, nonferrous corrosion prevention on most aluminum alloys.

Great resistance to corrosion on nonferrous materials including aerospace aluminums 6061, 7075, 2024, 3000

Water-clear, low-foaming and -misting, C290 is a joy to work with and manage

Provides good results in a wide range of grinding and machining operations

Easily removed from parts for easy cleanup before assembly, painting, or plating operations

PRTR compliant, no SARA 313 reportable chemistry. Product contains no chlorine, phenol, nitrites, copper, triazine, or silicone

Very low carryoff and long sump life results in low operating cost

Premium Synthetic Metalworking Fluid

TRIM C350 is a synthetic metalworking fluid optimized for the chemical, environmental, and machining requirements of the North American aerospace industry. C350 uses the best of the new ester technology to yield a very high performance, easy to use and maintain metal removal fluid. The combination of the proven synthetic ester technology and nonchlorinated EP package produces very high levels of usable lubricity at the point-of-cut. C350's unique chemical formula allows superior, nonferrous corrosion prevention particularly on aerospace aluminum alloys.

Meets the most stringent nuclear and aerospace chemical content and machining requirements

Superior resistance to corrosion on both nonferrous and ferrous materials including aerospace aluminums 7075, 2024, 3000, titanium, Inconel^®, brass, and high-strength alloy steels

Water-clear, low foaming, and misting, C350 is a joy to work with and manage

Provides superior results in a wide range of operations from general grinding to spar milling and turbine blade manufacture

Easily removed from parts for easy cleanup before assembly, painting, or plating operations

PRTR compliant, no SARA 313 reportable chemistry. Product contains no chlorine, phenol, nitrites, copper, triazine, or silicone

Very low carryoff and long sump life results in low operating cost

High-lubricity Honing Synthetic

TRIM C385 is a state-of-the-art synthetic coolant which provides excellent cooling and chip removal, good tramp oil rejection and machine cleanliness. C385 meets the need of the modern job shop for a single premium synthetic coolant for honing and virtually all machining operations.

Very low foam and mist

Great for form grinding, honing, boring, rolling, etc

Exceptional sump life and very good tramp oil rejection

Extremely low carry-off for very low total operating costs

Very low initial odor which usually disappears after 1-2 days

Compatible with dirty or grey cast iron cutting, grinding, and honing

Keeps your machines clean while leaving a soft, fluid film that protects the bare metal parts

The residual film is easily resoluble in the coolant working solution to facilitate easy machine cleaning and to minimize the buildup of sticky residues that can hold machine-destroying chips

High-performance for Hard Disk Drives

TRIM^® DRIVE CF2P is a specialized, chlorine-free, moderate-duty coolant formulated to meet the high-precision machining and stringent chemical restrictions of the Hard Disk Drive (HDD) industry. It has very good wetting and lubricity giving excellent surface finishes. Its ease of wash-ability makes DRIVE CF2P an excellent choice for HDD components manufacturers. TRIM DRIVE CF2P will run in high-pressure situations with little to no foam.

In addition to aluminum alloy, it is also suitable for a wide range of materials including steels and stainless steels

Low foam even in high-pressure operations without the use of silicone antifoam

Good hydrodynamic lubrication to perform reaming and threading applications

Excellent anti-weld properties without the use of either chlorinated or sulfurized EP additives

Keep machines very clean while leaving a fluid, oily residue for ease of cleaning and reduced machine maintenance costs

Does not require special disposal and is easily recycled

Non-staining on aluminum alloys commonly used to produce HDD components

After machining, parts can be washed easily and completely in aqueous washing systems

High-lubricity, Low-foam Semisynthetic

TRIM DRIVE G2 161C is a specialized, halogen-free, high lubricity semisynthetic coolant formulated to meet the high precision machining and stringent chemical restrictions of the Hard Disk Drive (HDD) industry. DRIVE G2 161C has very good wetting and lubricity giving excellent surface finishes. Its ease of wash-ability make DRIVE G2 161C an excellent choice for HDD components manufacturers. DRIVE G2 161C will run in high-pressure situations with little to no foam.

Suitable for a wide range of materials including aluminum alloys, steels, and stainless steels

Non-staining on aluminum alloys commonly used to produce HDD components

Low foam even in high-pressure operations without the use of silicone antifoam

Good hydrodynamic lubrication to perform drilling, reaming, and threading applications

Excellent anti-weld properties without the use of either chlorinated or sulfurized EP additives

Keep machines very clean while leaving a fluid, oily residue for ease of cleaning and reduced machine maintenance costs

Does not require special disposal and is easily recycled

Parts machined with DRIVE G2 161C can be washed easily and completely in aqueous washing systems

Long-life Emulsion

TRIM E206KS is a high quality universal emulsion coolant concentrate. It has been designed for a very broad range of metals allowing its effective use in most cutting and grinding operations, which requires minimal maintenance even in the most demanding fluid management systems. It has the lubricity and "guts" necessary to do heavy-duty machining. The stable and predictable performance of TRIM E206KS makes it a first choice for high-quality, consistent parts manufacturing.

Very stable formula provides long operational life with consistent performance

Has a very wide application range allowing its effective use on cutting and grinding

Extremely hard water tolerance

Extremely stable fine particle size emulsion to reduce carry-off and super-high penetrability to get the fluid to the point of cut

Provides good tool life and surface finishes

High tramp oil resistance for easy oil remove, longer coolant life and more opportunities to be recycled

Leaves a very light oily, non-gumming residue to prevent sticky ways, chucks, tool holders and fixtures

Coolant residue is easily removed with either water, working solution or aqueous cleaners

Good cleaning performance keeps machine tool very clean

Easy recycling or disposal with conventional techniques and equipment

Run effectively for long periods without the need for costly additives

Long-life Emulsion

TRIM™ E709 is high-quality, universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs. The stable and predictable performance of E709 makes it a first choice for high-quality, consistent parts manufacturing.

Very stable formula provides long operational life with consistent performance

Extremely hard water tolerant

Very wide application range, suitable for both grinding and machining

Fine particle size emulsion reduces carryoff and facilitates getting the fluid to the point of cut

In high-speed turning and milling, E709 has the right balance of cooling and lubrication to provide good tool life and surface finishes

Compatible with aluminum, steel alloys, cast iron, and yellow metals

Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders, and fixtures

Coolant is easily removed with water, working solution, or aqueous cleaners

Easy recycling or disposal with conventional techniques and equipment

Does not contain or test positive for phenol

Will run effectively for long periods without the need for costly additives

Long-life Emulsion

TRIM E709FF is a high quality universal emulsion coolant concentrate. It has been designed for a very broad range of metals allowing its effective use in most cutting and grinding operations, which requires minimal maintenance even in the most demanding fluid management systems. It has the lubricity and "guts" necessary to do heavy-duty machining. The stable and predictable performance of TRIM E709FF makes it a first choice for high-quality, consistent parts manufacturing.

Very stable formula provides long operational life with consistent performance

Has a very wide application range allowing its effective use on cutting and grinding

Extremely hard water tolerance

Extremely stable fine particle size emulsion to reduce carry-off and super-high penetrability to get the fluid to the point of cut

Provides good tool life and surface finishes

High tramp oil resistance for easy oil remove, longer coolant life and more opportunities to be recycled

Leaves a very light oily, non-gumming residue to prevent sticky ways, chucks, tool holders and fixtures

Coolant residue is easily removed with either water, working solution or aqueous cleaners

Good cleaning performance keeps machine tool very clean

Easy recycling or disposal with conventional techniques and equipment

Run effectively for long periods without the need for costly additives

Copper Alloy Machining Fluid

TRIM E711 is a high quality soluble oil designed primarily for the machining and grinding of yellow metals and copper alloys.

Rejects tramp oil to extend sump life

Will not stain or darken brass or other yellow metal alloys

Easy recycling or disposal with conventional techniques and equipment

Coolant is easily removed with water, working solution or aqueous cleaners

Very stable formula provides long operational life with consistent performance

Will not form the sticky, water insoluble residues commonly seen when machining yellow metals

Fine particle size emulsion reduces carryoff and facilitates getting the fluid to the point of cut

Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders, and fixtures

Compatible with all ferrous and nonferrous materials but is specifically designed for "free machining" yellow metals

Provides sufficient mechanical lubricity to run well in older "Swiss" style machines as well as in modern high speed CNC machines

Low Maintenance, General Purpose Emulsion

TRIM™ E712 is high quality universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs. It leaves a very easy to clean protection film on the work piece and machine parts to prevent corrosion on metal surface including the machine tool. The stable and predictable performance of TRIM E712 makes it a first choice for high-quality, consistent parts manufacturing.

Very stable formula provides long operational life with consistent performance

Extremely hard water tolerant

Very wide application range. Suitable for both grinding and machining

Fine particle size emulsion reduces carry-off and facilitates getting the fluid to the point of cut

In high-speed turning and milling, provides good tool life and surface finishes

Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders and fixtures

Coolant is easily removed with water, working solution or aqueous cleaners

Easy recycling or disposal with conventional techniques and equipment

Will run effectively for long periods without the need for costly additives. Easily recyclable and/or dispose with conventional recycling and/or disposal techniques

Magnesium Machining Emulsion

TRIM E738 is a soluble oil or chemical emulsion coolant concentrate designed for magnesium alloy machining. It provides excellent performance for high-temperature aerospace alloy and cast magnesium alloy. TRIM E738 consists of micro-molecular particles that provide advantages such as low mist levels, good cleaning and wetting performance. It provides mechanical lubrication, and is safe and very popular with operators.

Extremely hard water tolerable

High alkalinity reservation and release capability

Very tight emulsion particle structure that provides excellent wetting and cooling

Can reach cutting areas even in very high-speed cutting situations

Leaves a fluid residue to keep machine tool very clean

Prevents hydrogen and magnesium salts

Easy recycling or disposal with conventional techniques and equipment

Contains a highly effective extreme-pressure (EP) additive to control built-up edge (BUE)

Low-foam, High-lubricity Emulsion

TRIM E860 is a high-quality, general purpose emulsion for use on a broad range of ferrous and nonferrous metals, effective in most cutting and grinding operations. The stable and predictable performance of E860 makes it a first choice for precision and consistent parts manufacturing.

Very wide application range

Good hard water tolerance

Keeps machine tools clean

Works very well in general machining

Very stable formula provides good operational life with consistent performance

High tramp oil resistance for easy oil removal and longer coolant life

Easily recycled or disposed of using conventional techniques and equipment

Good balance of cooling and lubrication providing good tool life and surface finishes

Leaves a very light, oily, non-gumming residue to prevent sticky ways, chucks, tool holders, and fixtures

Extremely stable fine particle size emulsion allows for reduced carry-off and super-high penetrability to get the fluid to the point of cut

Premium, General-purpose Emulsion

TRIM E860KS is a high quality, general-purpose emulsion, which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs. It leaves a very easy to clean protective film on the work piece and machine parts to prevent corrosion on metal surfaces including the machine tool. The stable and predictable performance of TRIM E860KS makes it a first choice for high quality, consistent parts manufacturing.

Very stable formula provides long operational life with consistent performance

Extremely hard water tolerant

Very wide application range

Suitable for both grinding and machining

Fine particle size emulsion reduces carry-off and facilitates getting the fluid to the point of cut

In high-speed turning and milling, provides good tool life and surface finishes

Protects machine and tool surfaces while also preventing sticky ways, chucks, tool holders, and fixtures

Coolant is easily removed with water, working solution or aqueous cleaners

Easy recycling or disposal with conventional techniques and equipment

Will run effectively for long periods without the need for costly additives

Works very well in general machining where traditional soluble oil may not cool sufficiently

High Performance Emulsion

TRIM E9010BX is a soluble oil coolant concentrate designed as a general purpose multi-metal coolant for general machining of ferrous and nonferrous materials. It has the lubricity and "guts" necessary to do heavy-duty machining center work and still provide the wetting and cooling necessary to do high-speed turning and grinding operations.

Contains a proven and highly effective extreme-pressure (EP) additive to control built-up edge (BUE)

Has a very wide application range allowing its effective use on such diverse operations as production, surface and centerless grinding, heavy duty broaching, gear hobbing and replacing straight oil on some types of screw machines

Extremely stable fine particle size emulsion to reduce carryoff and to facilitate getting the fluid to the point of cut

Rejects tramp oil to help extend sump life and increase recycling options

Leaves a oily fluid, nongumming residue to prevent sticky ways, chucks, tool holders, and fixtures

Coolant residue is easily removed with either water, working solution, or aqueous cleaners

Easy recycling or disposal with conventional techniques and equipment

Chlorine-free, High-performance Emulsion

TRIM E925 utilizes a proprietary lubricity package to deliver exceptional surface finish and tool life on difficult-to-machine aerospace materials. Designed to lower total cost and improve manufacturing efficiency thanks to extended sump life. Environmentally friendly emulsion is free of boron, chlorinated paraffins, and other halogens. Mild contact nature and low initial-charge odor provide an operator friendly environment.

Extended sump life for lower operating costs

Protects sensitive aluminum and nonferrous alloys

Excellent lubricity without chlorinated paraffins

Provides superior results in a wide range of operations

Superior corrosion resistance

Appropriate for most high-pressure systems

Low product odor

Mild operator contact properties

Soft fluid film protects chucks, ways, and tool holders

Rinses off for easy parts cleanup before assembly, painting, or plating

High Performance Machining Emulsion

TRIM E950 is a proprietary blend of new vegetable-based technology and premium traditional lubricity additives to yield a very high performance, low management metal removal fluid. This premium emulsion product is operator friendly because of its mild contact nature and low chemical initial-charge odour. TRIM E950 is robust enough to deliver extended useful life and avoid rancid odours normally associated with traditional emulsions. The unparalleled lubricity delivers exceptional surface finish and tool life on difficult to machine aluminium alloys, inconel, titanium, stainless and high tensile strength steels.

Delivers unparalleled lubricity

Very long sump life and low carry-off rates result in low operating cost

Low foam even in soft water areas

Hard water tolerant

Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE) in tough operations on aerospace materials

Fine emulsion ensures fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior tool life and corrosion prevention

Compatible with all materials excluding magnesium

Easily recycled or disposed of without special handling or equipment

Will run effectively for long periods without the need for costly additives

Carbide Grinding Synthetic

TRIM GRIND WC minimizes cobalt leaching in the grinding of tungsten carbide (WC) and other high cobalt materials. Minimal cobalt leaching means increased piece part integrity, while improving "G RATIOS" and reducing grinding forces. GRIND WC is specifically designed for the carbide grinding industry; it will also perform very well in grinding ceramics, cermets, and tool steels.

Keeps super-abrasive wheels clean while not attacking super-abrasive wheel bonding systems

Carries grinding swarf to the filter, but will release swarf in properly designed settling tanks

Is not stripped out by conventional filtration systems

Operators like GRIND WC’s clear working solution for superior visibility while grinding

Exceptional sump life and good tramp oil rejection for easy skimming

Resists oxidation and varnishing

Resists cobalt leaching for improved operator safety, stronger parts, and cleaner machines

Very low carryoff equals low fluid makeup costs

Easy recycling or disposal with conventional techniques and equipment

Cutting and Grinding Fluid Concentrate

TRIM HM is a synthetic cutting and grinding fluid concentrate. It was developed to facilitate the manufacture of cutting tools from High-Speed Steels (HSS), Chill Cast Alloys, and other high-strength, high-hardness tool materials. TRIM HM is intended for situations where high-heat removal and low working concentrations are critical. TRIM HM is particularly well suited for surface grinding and similar operations requiring maximum heat transfer. It is often used effectively in double disc grinding, belt grinding, and abrasive cutoff operations on ferrous materials.

Is water clear with a fluorescent green tint to facilitate the operators' view of the work piece

Even at very low concentrations it has extended sump life

Settles chips and swarf rapidly and lends itself to very high flux rates in positive media filtration

Low mist and odor

Very low foam even at very high pressures and flow rates

Low foaming wetting agents to keep the wheel clean and prevent wheel loading

Will not attack super abrasives or their wheel bonding systems

Coolant residue is easily cleaned up with either water or working solution

Rejects tramp oil for easy skimming and recycling

Easy recycling or disposal with conventional techniques and equipment

Low-foam Ferrous Semisynthetic

TRIM MicroSol 456 low-foam semisynthetic, microemulsion coolant is optimised for high-volume cast iron, ferrous, and some aluminium and nonferrous metalworking operations. MicroSol 456 prevents leaching of elemental iron and eliminates clinkering and oxidation of ferrous micro fines.

Delivering extended sump life, machine-friendly MicroSol 456 provides excellent, cost-effective cooling. Make a difference to your bottom line with MicroSol 456.

Low foaming for today's demanding high-pressure, high-volume applications

Also for machining some aluminium alloys and nonferrous metals

Provides superior corrosion inhibition on cast iron and eliminates "hot chip" and clinkering problems

Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance

Requires no special disposal or recycling

Extended-life, Nonchlorinated Semisynthetic

TRIM MicroSol 585XT is a high-lubricity, semisynthetic, microemulsion coolant. The formula delivers extended sump life and better foam control versus previous generation semisynthetics. It provides excellent cooling and mechanical lubricity, along with the machine-friendly characteristics you expect from a premium TRIM coolant. While it is particularly well suited for machining and grinding gray iron, it does very well in mixed metal situations. MicroSol 585XT has proven to be an exceptional machining fluid for titanium alloys.

Dramatically extends useful life without the need for tank-side biocides or fungicides

Low foaming for todays demanding high-pressure, high-volume applications

Compatible with a very wide range of material including cast iron, steels, copper, titanium, and aluminum alloys, and many plastics and composites

Optimized combination of cooling and lubricity for titanium machining applications

Provides superior corrosion inhibition on cast iron and eliminates "hot chip" and clinkering problems

Excellent alternative to chlorinated soluble oils on high-silica aluminum alloys

Contains no nitrites, triazines, phenols, and chlorinated or sulfurized EP additives

Provides superior corrosion inhibition on all ferrous and nonferrous metals

Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance

Uses standard metalworking recycling and disposal techniques

Advanced Technology Aerospace Semisynthetic

TRIM MicroSol 590XT is an environmentally-friendly semisynthetic, microemulsion coolant formulated to pass aerospace approval test requirements. It utilizes the newest technology to provide long life and excellent protection of sensitive alloys. MicroSol 590XT improves on the proven performance of previous generations with a robust stability package using the most environmentally-safe ingredients. The formula is a favorite of environmental advocates, safety professionals, and demanding production managers.

Meets the most stringent aerospace specifications and has received many aerospace approvals

Protects and prevents corrosion on sensitive alloys, including aerospace and nuclear materials

Free of chlorine, triazine, formaldehyde releasers, phenols, boron,and secondary amines

Dramatically extends useful life without the need for tank-side biocides or fungicides

Low foaming for todays demanding high-pressure, high-volume applications

Optimized combination of cooling and lubricity for titanium, aluminum, steel, stainless steel, and Inconel^® machining applications

Excellent alternative to chlorinated soluble oils on high-silica aluminum alloys

Provides superior corrosion inhibition on all ferrous and nonferrous metals

Keeps parts and machines very clean to reduce maintenance and production time

Premium High-lube PRTR Microemulsion

TRIM MicroSol 687NXT is a translucent, premium high-lube, PRTR compliant microemulsion. The product is low foaming in soft water but is also stable in hard water. The product is designed to machine difficult to machine metals, such as stainless steel and Inconel. It is also good for most aluminum alloys including aerospace grade.

Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance

Excellent compatibility with a very wide range of material including stainless steel, nickel alloys, titanium, and aluminum alloys

Greatly extends useful life without the need for tank side biocides or fungicides

Low foaming for modern high-pressure, high-volume applications

Uses standard metalworking recycling and disposal techniques

Does not contain any chemical listed under Japan PRTR regulation

Provides superior corrosion inhibition on all ferrous metals

High-lubricity, Low-foam Premium Semisynthetic

TRIM MicroSol 690XT is a high-lubricity, semisynthetic, microemulsion coolant. The formula delivers extended sump life and better foam control versus previous generation semisynthetics. It provides excellent cooling and mechanical lubricity, along with the machine friendly characteristics you expect from a premium TRIM coolant. It does very well in mixed metal situations and is compatible with a very wide range of materials including titanium, high nickel alloys, steels, copper, and aluminum alloys.

Dramatically extends useful life without the need for tank-side biocides or fungicides

Boron and halogen free

Low foaming for todays demanding high-pressure, high-volume applications

Compatible with a very wide range of materials including titanium, high nickel alloys, steels, copper, and aluminum alloys

Excellent alternative to chlorinated soluble oils on high-silica aluminum alloys

Contains no nitrites, triazines, phenols, chlorinated, or sulfurized EP additives

Provides superior corrosion inhibition on all ferrous and nonferrous metals

Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance

Uses standard metalworking recycling and disposal techniques

Premium, High-lubricity, Low-foam Microemulsion

TRIM MicroSol 692XT is a high-lubricity, semisynthetic, microemulsion coolant. This formula delivers extended sump life, greater bio stability, and better foam control versus previous generation semisynthetic Microemulsions. It does very well in mixed metal situations and is compatible with a very wide range of materials including titanium, high nickel alloys, steels, copper, and aluminum alloys. Improved tramp oil rejection keeps your production running smoothly. Increase your profitability and production with TRIM MicroSol 692XT!

Improved lubricity for longer tool life

Dramatically extends useful life without the need for tank-side biocides or fungicides

Halogen free

Low foaming for todays demanding high-pressure, high-volume applications

Excellent alternative to chlorinated soluble oils on high-silica aluminum alloys

Provides superior corrosion inhibition on all ferrous and nonferrous metals

Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance

Requires no special disposal or recycling techniques

Minimum Quantity Lubrication Fluid

TRIM MQL™ 100 is a high performance, vegetable-ester based micro lubrication fluid. It is fully compatible with all “micro lube” and micro mist systems. MQL 100 contains a blend of environmental and operator friendly materials that provide very high levels of EP and boundary lubrication to control built up edge (BUE) and sliding friction. MQL 100 outperforms the competition in sawing, drilling, tapping, and milling, to name but a few. In situations where it is impractical to use a micro lubrication applicator, MQL 100 may be manually applied to the tool or work piece.

Very low mist

Environmentally friendly, renewable resource based

Low consumption, out-performing the more expensive products

Easily water washable – does not produce hard to remove residues

Promotes superior finish and tool life and is compatible with all materials

Has been extensively tested and proven in all major brands of micro lube applicators

Very high levels of lubricity with minimum quantities of material at the point of cut for high material removal

High Performance Tool Grinding Oil
5 drum∗ minimum batch order size. Pricing and delivery available upon request.

TRIM OG108 is a very high specification grinding oil formulated for carbide and HSS tool grinding operations. The product utilizes a very highly refined hydrocracked base oil which ensures very low levels of mist and high flash point. TRIM OG108 has been formulated to provide excellent wheel flushing properties together with good friction reduction and workpiece cooling.

Very highly refined base oil ensures low mist and high flash point

Good flushing properties keeps grinding wheels very clean

Excellent friction reducing properties ensures long wheel life

Excellent heat transferring properties

Excellent oxidation stability

Highly filterable in pre-coat filter systems

Low foaming

No reaction with cobalt

Kind to machine components and elastomers

Light color and low odor for good operator acceptance

High Flash Point Gear Grinding Oil

TRIM OGM100HF is a high-efficiency grinding oil composed of high-quality mineral oil and various high-quality oil additives. This product has good permeability and lubricity, and can be used in the grinding process of materials (especially gear grinding) like cast iron, alloy steel, stainless steel, etc. It is also suitable for various profile grinding, internal and external grinding, cutting, centerless grinding, and other grinding processes.

Does not contain phosphorus or heavy metals, which protects the environment and reduces pollution

Light color, low odor

Good material compatibility

Safe and non-irritating to the skin

Produces good surface finishes

Provides high-strength lubricity in various medium-to-heavy-duty machining operations

Meets the cutting requirements of various machining operations: such as, automatic lathes, special machines, CNC lathes, and machining centers.

High-performance, Cutting and Grinding Oil

TRIM OM 210 is a low-odor, light-colored oil designed for operations where low viscosity and high lubricity are required. In addition to general machining, OM 210 is particularly effective in deep-hole drilling and creepfeed grinding where its ability to flow into the cutting zone and "wet" the surfaces increases tool life and reduces heat.

Light color and low odor

High flash point

Minimal carry over loss

Excellent chips flushing and low foam

Oxidation inhibited for longer life

Excellent tool life properties

Nonchlorinated Cutting and Lubricating Oil

TRIM OM 303 is a highly formulated straight oil designed for use in conventional and Swiss style screw machines, high-speed turning centers, and high-performance, multi-station machines, such as Hydromats. OM 303 is safe for use on aluminum alloy and steel alloy parts, as well as cast iron, copper, brass, and bronze. This product is excellent for high-pressure applications such as thread rolling and thread-form tapping. OM 303 has proven itself in difficult operations on stainless and bearing steels. OM 303 provides lubrication properties similar to ISO 32 general-purpose lube oils.

Very light colored and clean running

Low foaming and low misting for use in aggressive operations

Oxidation inhibited for longer life, and an excellent choice where both ferrous and aluminum or copper alloy parts are being machined aggressively

Far easier to wash off parts than many oils of similar or even lower performance

Has replaced dark, active sulfur/chlorine straight oils in several large operations while providing superior results in tool life

An outstanding product in thread rolling, thread form tapping, and in Swiss screw machines with solid bushings

Contains no active sulfur; therefore, does not stain parts

Heavy-duty Cutting Oil

TRIM OM350C is a heavy duty, mineral oil based cutting oil formulated with high performance synthetic ester-based additives. It can be used for a variety of metal cutting and grinding processing, especially suitable for steel broaching. This product is also suitable for tapping, milling, and reaming processes. Also suitable for multi metal applications such as copper alloy, aluminum alloy, and heat-treated steel.

Excellent extreme pressure lubrication, inhibiting BUE generated, providing an excellent surface finish

Provides excellent lubrication and cooling for machining deep holes

Low oil mist, low volatility, maintains a clean working environment

Microemulsion Semisynthetic

TRIM™ SC310 is a high-oil, semichemical coolant. This product combines the cooling, rust inhibition, and wetting of a premium synthetic with the mechanical lubricity and machine "friendliness" of a soluble oil. SC310 is well-suited for general, high-speed machining and grinding of all materials.

Compatible with a very wide range of material including: cast iron, steels, copper, and many plastics and composites

Provides superior corrosion inhibition on all ferrous and nonferrous metals and eliminates “hot chip” and clinkering problems often seen when machining cast iron

Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance

Has exceptional sump life and very low makeup for extremely low total operating cost

Low odor and mist makes for an operator-friendly product

Extremely effective EP additive package

Contains no nitrites, heavy metals, phenolic compounds

Easy recycling or disposal with conventional techniques and equipment

Chlorine-free Semisynthetic Coolant

5 drum^∗ minimum batch order size. Pricing and delivery available upon request.

TRIM SC410 is a chlorine-free, semisynthetic coolant using vegetable-derived and ester lubricants. It is very clean running in moderate-duty machining and grinding of both ferrous and nonferrous materials. In addition to its broad range of machining qualities, it has been specially optimized for machining "gray iron"castings and for surface and cylindrical grinding of ferrous materials.

Based on our exclusive ester lubricant technology, contains no mineral (petroleum) oil

Low foaming in most operations

Compatible with a very wide range of materials including ferrous, nonferrous, and nonmetallic material

Will provide superior sump life and corrosion inhibition for long periods of time without adds

Prevents chip "clinkering" and "hot" chip hoppers when machining cast iron

Will keep the machine and work environment clean even when machining or grinding gray iron

Contains no chlorine or sulfur-based additives

Contains no nitrites, sulfonates, Alkylphenol Ethoxylates, or phenols and is not SARA 313 reportable

Very low carryoff and long sump life, delivering low operating costs

Hard water tolerant up to 30 grains

High-performance Semisynthetic Fluid

TRIM SC538 a high-performance semisynthetic coolant. Provides superior aluminum machinability, boundary lubrication, and produces a very high quality surface finish. Can also be utilized for ferrous and non-ferrous metal materials, stainless steel, and aerospace alloy materials. SC538 has good lubricity and friction reducing qualities in high-speed cutting and grinding applications.

Provides superior aluminum machinability

Very high quality surface finish

Has exceptional sump life and very low makeup for extremely low total operating cost

Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance

Low odor and mist makes for an operator friendly product

Easy recycling and disposal with conventional techniques and equipment

General Purpose Semisynthetic

TRIM SC639 is a general purpose semisynthetic cutting and grinding fluid concentrate which provides an excellent balance between cooling and lubricity. SC639 has very good corrosion protection for both ferrous and non-ferrous metal, and can be used for a wide range of high-speed turning and grinding operations. SC639 leaves a thin layer of water soluble oil residue that provides extra protection to the machine tools parts while keeping the machine clean.

Provides excellent lubricity for various machining applications

Provides excellent corrosion and rust inhibition on ferrous and nonferrous alloys, preventing clinkering problems of cast iron chips in machining

Keeps machines very clean and leaves a soft fluid film for easy cleaning and less machine maintenance

Long sump life and low coolant consumption that reduce the cost for user

Low odor and mist that provides a good working environment

Good hard water tolerance up to 40 grain

Easy recycling or disposal with conventional techniques and equipment

High-lubricity Semisynthetic

TRIM SC9030 is a high-oil semisynthetic coolant. This product provides the cooling, rust inhibition, and wetting of a premium synthetic with the mechanical lubricity and machine "friendliness" of a soluble oil. TRIM SC9030 is well suited for general high-speed machining and grinding of all materials and it leaves soluble emulsion oil as residue.

Compatible with a very wide range of materials including cast iron, steels, copper, aluminum alloys, and many plastics and composites

Provides superior corrosion inhibition on cast iron and other ferrous and nonferrous materials; and eliminates the "hot chip" and clinkering problems often seen when machining cast iron

Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance

Has exceptional sump life and very low makeup for extremely low total operating cost

Low odor and mist makes for an operator-friendly product

Easy recycling or disposal with conventional techniques and equipment

High-lubricity Tapping Fluid

TRIM TAP HEAVY is a 100% synthetic and vegetable-based lubricant possessing strong friction-reducing properties. Designed as a tough operation product for use with metals of low machinability, it's recommended for use at full-strength, brush-on use for reaming, tapping, and threading.

Especially for taps ½" diameter and larger

Contains no mineral oils

Promotes excellent finish

Ensures parts size control

Delivers exceptionally long tool life

Reduces rubbing of the tool flank

Water washable, for easy parts cleaning

Compatible with most TRIM fluids

Use for added lubricity on extremely tough jobs

Tapping Fluid

TRIM TAP LIGHT is a synthetic/vegetable/mineral oil blend possessing strong friction-reducing properties. Use with metals of low machinability; specifically recommended at full strength for flooding applications involving broaching, sawing, milling, tapping, threading, gear cutting and shaving, gundrilling, and reaming.

Especially for taps ¼" diameter and smaller

Promotes excellent finish

Ensures parts size control

Delivers exceptionally long tool life

Reduces rubbing of the tool flank

Water washable, for easy parts cleaning

Compatible with most TRIM fluids

Use for added lubricity on extremely tough jobs

Nonferrous Corrosion Inhibitor

TRIM TC 155 is a nonferrous corrosion inhibitor for use in water soluble and straight oil systems. It is particularly effective in preventing staining and white rust on die cast alloys containing copper.

Prevents staining and white rust on die cast alloys containing copper

Nonferrous corrosion inhibition

Chlorinated Lubricity Additive

TRIM TC 175 is a chlorinated EP (extreme pressure) lubrication/emulsifier additive package. It may be added to water-soluble coolant systems to replace or increase the presence of the chlorine EP additives in the system.

New, easier to mix formulation

New, chlorine EP additives stay in systems longer

Odor Mask

TRIM TC 177 is a "vanilla" odor mask. This product may be used to reduce some of the odors associated with coolant systems.

"Vanilla" odor mask

Antifoam

TRIM TC 241A is a long lasting antifoam that does not contain any of the silicone or poly-siloxane ingredients usually found in antifoam. This unique formula results in much longer functional life when compared to traditional antifoams.

Only add to synthetic fluids

Use 0.01 (100 PPM) as the add rate

Pre-mix in either clean water or coolant working solution

Adding a little at a time, “up stream” of the filter helps to ensure maximum effectiveness

When properly mixed into the working solution, TRIM TC 241A will pass through filtration down to 2 microns, however, when not properly mixed, it may be filtered out

This material is very stable, and when properly mixed, three to four weeks between adds is typical

Fluid temperatures must be 21°C or higher at the point of agitation

Dewatering-fluid 104°F (40°C) flash point

WEDOLiT AS 1012 is a dewatering fluid with corrosion protection properties. It uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can efficiently be dewatered. It is mainly used as an immersion bath at room temperature.

Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions or synthetic coolants are removed from the metal surface

After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage

Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off

Development of a clear phase boundary between the water and the product, without forming an emulsion phase

Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils

Excellent bath-life

Additive loss due to water contact: None

Long term DW Fluid 104°F (40°C) flash point

WEDOLiT AS-2251 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

Stable against acidic and alkaline contamination

Good material compatibility

Water displacing with very good wetting behavior

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Additive loss due to water contact: Very low

High-Protection-Waxdispersion-Fluid 104°F (40°C) flash point

WEDOLiT AS 2603 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited storage period for outdoor storage. It can be applied by spraying, flooding, brushing or rolling.

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface

Good protection for outdoor storage

It´s recommended to homogenise the product before use or after a longer storage period

Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)

High-Protection-DW-Fluid 140°F (60°C) flash point, thin film

WEDOLiT AS-4116 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing of rolling.

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

Stable against acidic and alkaline contamination

Good material compatibility

Water displacing with very good wetting behavior

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Additive loss due to water contact: Extremely low

Water-soluble fully synthetic passivating agent

WEDOLiT AW 5040 is a water-soluble passivating agent for steel, which is used as an aqueous solution for a short-term corrosion protection. The product contains no oily or fatty substances and is free of sodium nitrite. Furthermore, it contains a copper and brass inhibitor (for the protection of fittings, etc.).

Almost foam free

While the protecting film remains water soluble, the product is suitable as a short-term corrosion protection of steel (covered storage)

Good skin compatibility

Water-miscible High-performance Fluid

WEDOLiT AW 8321 is universally applicable for parts cleaning and corrosion protection. This mineral oil based product is not only suitable for steel, but also for non-ferrous metals. Utilizing the latest technology, AW 8321 offers the possibility for a boron and formaldehyde free application.

The product forms a stable emulsion, regardless of the concentration. Due to the electrolyte and temperature stability, an application in heated baths is possible (recommended temperature 140 - 176°F, (60 - 80°C))

Even at high temperatures the product is stable against contaminations (e.g. sodium sulfonates or phosphates)

Easily removable with solvents or alkaline industrial cleaners

For the corrosion protection it´s important that treated parts are completely dry before packaging. Dependent on the concentration a minimal to slightly noticeable film is formed on the metal surface

Very good compatibility with VCI foils

Outstanding material compatibility (even at higher concentration)

Water-miscible, fully synthetic coolant

WEDOLiT CS 8208 is suitable for ultrasonic testing systems. The product is also suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 5 - 10%). Not suitable for the manufacturing of workpieces made of zinc, aluminum and their alloys.

Offers high cooling- and flushing properties with a very good wetting behavior

Contributes to a high tool life

Very good application stability

Almost free of foam

Offers a good skin compatibility

Due to its thermal stability, the product can be used in almost the whole process chain of welded tubes (forming, welding, calibration, sawing)

High performance expander oil

WEDOLiT EP 1090-E is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents the stick-slip- effect due to the high content of polar additives.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by the utilization of specific additives

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander oil

WEDOLiT EP 435 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander Oil, Easy-splitting Technology, mineral oil based

WEDOLiT EP 540 ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and due to the high content of polar additives, prevents the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and expander heads and can be easily separated into water and oily waste by utilizing specific additives

Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander oil

WEDOLiT EP 760 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander Oil, Easy-splitting Technology, mineral oil based

WEDOLiT EP 760 ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and due to the high content of polar additives, prevents the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by utilizing specific additives

Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

High-performance forming oil

WEDOLiT FN 1190-2300 is a highly viscous, chlorine containing forming oil for tube drawing and other cold forming operations of stainless steel. The undiluted product is usually applied by brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behavior

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behavior, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieving dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Soluble in chlorinated hydrocarbons

Chlorine free stamping oil

WEDOLiT FN 4455-55 is a low viscous, water-insoluble lubricant for heavy forming operations of steel and non-ferrous metals. A combination of EP additives offers a outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushing, or rolling.

Stable load carrying capacity and a homogenous sliding behavior

Reduces friction and wear and thus contributes to a long tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behavior, prevents stick-slip and chatter

Leads to clean surfaces and contributes to dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

High performance forming oil

WEDOLiT FN 6160-90 is a water-insoluble, chlorinated lubricant for deep drawing and other cold forming operations, e.g. wire drawing, extrusion, or thread forming of steel and stainless steel. The undiluted product is usually applied by flooding, spraying, brushes, or by means of rollers.

Stable load carrying capacity and a homogenous sliding behavior

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behavior, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieve dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Special forming oil

WEDOLiT FN 8471 is a chlorine free, pasty, water-insoluble lubricant for cold forming processes (e.g. pilgering) of high alloyed steels. The product is usually applied by brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behavior

Reduces friction and wear and thus contributes to a high tool life

The outstanding extreme-pressure properties combined with an exceptional adhesion offers the possibility for high degrees of deformation

Stable cold start behavior, prevents stick-slip and chatter

Contributes to achieving dimensional accuracy

Before pilgering: Sicromal steels should be pre-heated to 200 - 280°C

Pigments will remain on the surface after annealing and should be removed (e.g. by pickling with HCl or HNO₃) before further processing

Special forming oil

WEDOLiT FN 8830 is a chlorine free, pasty, water-insoluble lubricant for cold forming processes (e.g. pilgering) of high alloyed steels. The product is usually applied on the outer diameter by brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behavior

Reduces friction and wear and thus contributes to a high tool life

The outstanding extreme-pressure properties combined with an exceptional adhesion offers the possibility for high degrees of deformation

Stable cold start behavior, prevents stick-slip and chatter

Contributes to achieving dimensional accuracy

Pigments will remain on the surface after annealing and need to be removed (e.g. by pickling with HCl or HNO₃) before further processing

Straight Cutting and Bending Oil

WEDOLiT FS 3910 is non-water-soluble cooling lubricant with low viscosity for punching- and bending operations on steel and zinc coated steel. The product is not applicable for the treatment of nonferrous metals.

Can be applied undiluted by spraying, flooding, brushing or rolling

Has a good spread effect, which causes an optimal even wettability of metal surfaces

Has a simultaneously cleaning effect

Contains a combination of aromatic free solvents with additives of esters and extreme-pressure compounds and is therefore practically odorless

Is marked by a very fast evaporation with high flash point

Solvent base for aluminum stamping 158°F (70°C)

WEDOLiT FS 4710 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminum and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushes, or by means of rollers.

Good spreading behavior, which leads to a uniform wetting of the metal surface

Stable load carrying capacity and a homogenous sliding behavior

Reduces friction and wear and thus contributes to a high tool life

Leads to clean surfaces and contributes to achieving dimensional accuracy

If the product is finely dispersed, it evaporates after a short time without leaving any residue. Therefore, an additional cleaning step is not necessary. Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners

Water-soluble, fully synthetic, good material compatibility

WEDOLiT FW 3500 is a high-pressure agent for hydroforming-processes such as internal and external high pressure forming of steel plates, with different surface qualities and thicknesses. The product can also be applied in different grinding and cooling operations.

Approved by “FF Fluid Forming“

Offers very good high-pressure properties

Contributes to a high tool life

Very good application stability

Almost free of foam

Offers very good skin compatibility

Recommended mixing ratio

Hydrofroming:  from 5 - 10%

Grinding:  from 3 - 6%

Water-miscible, fully synthetic coolant for the whole tube welding line

WEDOLiT FW 7651 is suitable for the manufacturing of welded steel tubes. It fulfills the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)

No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)

Can be centrifuged without loss of active substances

Removable with organic solvents or alkaline industrial cleaners

A bright workpiece surface is obtained after annealing

Recommended mixing ratio

Tube welding:  from 4 - 6%

Water-miscible, fully synthetic coolant

WEDOLiT FW 7652 is suitable for wire drawing as well as for the manufacturing of welded steel tubes. It fulfills the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)

No emulsification of mineral oils and engine lubricants. Therefore, the application of a corrosion inhibition oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)

Can be centrifuged without loss of active substances

Removable with organic solvents or alkaline industrial cleaners

A bright workpiece surface is obtained after annealing

Recommended mixing ratio

Tube welding:  from 4 - 6%

Wire drawing:  from 3 - 12%

Water-miscible, fully synthetic coolant

WEDOLiT FW 7661 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 3 - 5%).

Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)

No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacturing of profiled tubes)

Can be centrifuged without loss of active substances

Removable with organic solvents or alkaline industrial cleaners

A bright workpiece surface is obtained after annealing

Recommended mixing ratio

Tube welding:  3 -5%

Emulsion for the whole tube welding line

WEDOLiT FW 7840 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration from 7%).

The product is approved by Mercedes-Benz Group AG (formerly Daimler AG) (QSO 040305) under the name WEDOLiT K 911.

Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)

Can be centrifuged without loss of active substances

Removable with organic solvents or alkaline industrial cleaners

A bright workpiece surface is obtained after annealing

Recommended mixing ratio

Tube welding:  from 7%

Universal cutting oil

WEDOLiT N 52 is a mineral-oil based high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems such as milling, sawing, or thread forming steel, aluminum, and non-ferrous metals*.
Approved by Rattunde & Co as a cutting oil for minimum quantity lubrication.

Stable load carrying capacity and a homogenous sliding behavior

Very good wetting ability and film formation without adhesion

The outstanding cooling and lubrication properties lead to significantly reduced friction and wear and thus contribute to a long tool life

Leads to clean surfaces and contributes to achieving dimensional accuracy

Economical application

Easily removable with organic solvents or alkaline industrial cleaners

Economical Heavy-duty Spray Cleaner

Master STAGES™ CLEAN 2017 is an economical heavy-duty spray cleaner that removes heavy soils and oily residues from ferrous and magnesium parts. Often used in rebuild operations and for cleaning up cast iron, stamped or drawn steel parts, or removing heavy RP coatings.

Very economical way to remove heavy soils and light rust

Low foaming at ambient temperatures, and even lower when used above 120°F (49°C)

Can be recycled using XYBEX equipment

Contains no solvents, borates, silicates, nitrites, or amines

Long bath life

Excellent compatibility with magnesium

Will prevent flash rusting and provide one-to-two days of in-process corrosion inhibition if not rinsed

Parts Washing Fluid with Corrosion Inhibitor

Master STAGES™ CLEAN 2029 "One Step" is a highly concentrated cleaner/corrosion inhibitor designed for spray washers and immersion tanks. This product will remove heavy soils and provide two-to-four weeks of indoor corrosion inhibition on steel and cast iron parts.

Formulated without silicates or other high pH additives, CLEAN 2029 "One Step" is compatible with ultrafiltration systems and bioremediation

An excellent choice for cabinet-style spray washers and can be used for washing steel, stainless, cast iron, titanium, and many aluminum alloys

Hard water tolerant, it provides long bath life

Environmental approvals are simplified because CLEAN 2029 "One Step" contains no nitrites, barium, phenols, or butyl cellosolve

This formula has very low V.O.C. content and no SARA 313 reportable ingredients

Low foaming for use in high-pressure spray washers with temperatures above 140°F (60°C)

Washing Compound for Ultrasonic and Immersion Washers

Master STAGES™ CLEAN 2039 is a concentrated, very high performance cleaner made for washing all metals including cast iron and alloy steels. CLEAN 2039 can be used in spray-type and ultrasonic cleaning of light oils. CLEAN 2039 cleans the oil and metal residues off of the parts, while leaving a thin protective film to provide strong corrosion inhibition on ferrous metals. It is a good choice for cleaning cast iron parts.

Provides strong corrosion inhibition

To extend CLEAN 2039's wash bath life, it is very easy to remove tramp oils by using the XYBEX SCROUNGER™ or SCROUNGER™ JR Oil Skimmers

Low foam even in the high-pressure washers

Low-foam Spray Washing Compound

Master STAGES™ CLEAN 2115AL is an aluminum compatible, high-performance, low-foam synthetic washing compound for use in very high-pressure spray washers, de-burring, and water jet cutting. Advanced surfactant technology provides excellent foam control and tramp oil rejection.

Compatible with a wide range of materials including aluminum, cast iron, steels, zinc, plastics, and composites

Resists foaming even when contaminated with large quantities of soils or coolant. This makes CLEAN 2115AL an excellent choice where rapid buildup of coolant carryover creates a foam problem

Many CLEAN 2115AL applications are in the range of 3,000 to 10,000 PSI (20684 to 68947 kPa)

Provides short-term corrosion inhibition on cast iron and ferrous alloys

Excellent biostability

Extremely low carryoff keeps operating costs down

Low foam and mist

Very low initial odor level

Exceptional sump life and great tramp oil rejection

Residue-free, Multi-metal Cleaner

Master STAGES™ CLEAN 3011 is a concentrated multi-purpose fluid that excels as a liquid parts washing compound or corrosion inhibitor and does not foam even at room temperature in high-pressure spray washers. It will remove light oils and water soluble cutting and grinding fluid residues and leave behind a thin rust inhibiting film for in-process corrosion inhibition of ferrous parts. CLEAN 3011 is also safe for use on aluminum alloy, copper, brass, bronze, and zinc. CLEAN 3011 is an excellent choice in cast iron operations where it can be used for cleaning and rust inhibition with excellent biostability.

Silicate, phosphate, and boron free

Leaves no powdery residue

Low foaming for use in high-pressure spray washers or grinders and has excellent hard water stability

Has a moderate pH, excellent anti-corrosion, and does not require rinsing, making it an excellent short-term, in-process corrosion inhibitor

CLEAN 3011 maintains its alkalinity and biostability for long periods of time and will tolerate stagnant conditions such as leak test baths and hydrostatic leak testing applications

Washing Compound for Ultrasonic Immersion and Spray Washers

Master STAGES™ CLEAN 9640XT is a concentrated, very high performance cleaner made for washing all ferrous metals including cast iron, alloy steel and other metal parts cleaning, and provide a strong rust –proof function between processes. CLEAN 9640XT can be used in spray-type cleaning and ultrasonic cleaning of light oil. It can clean the oil and metal liquid residue of the parts, and leave a thin layer of protective film which provides the rust-proof of ferrous metal. CLEAN 9640XT has good anti-rust and anti-corrosion. It is a good choice for cleaning cast iron parts.

Very good rust prevention, fits to high requirement rust cleaning processes

Strong ability to resist oil

It is very easy to separate out oil by using SCROUNGER & SCROUNGER JR to extend the service life

In the usual heating conditions, CLEAN 9640XT can keep a low foam even in a high pressure washer

Silicated Low-foam Cleaner

Master STAGES™ CLEAN IP 2019s is a very low-foaming, liquid, cleaning concentrate designed to remove straight oils and coolants from steel, cast iron, and most aluminum parts.

An excellent cleaner and very economical to use

Compatible with aluminum, cast iron, and steel alloys

Rejects oil for easy skimming or centrifuging to extend bath life

Nonfoaming at high-pressure in a spray washer and vibratory deburring machines even at room temperature

Provides flash corrosion inhibition and up to two weeks of short-term, dry, in-process corrosion inhibition

Low V.O.C. Emulsion Corrosion Inhibitor Concentrate

Master STAGES™ NOCOR E6 is a super-concentrated, barium-free, water-based emulsion rust inhibitor that will protect steel, cast iron, and other ferrous parts from in-plant corrosion for up to six months. Parts coated with NOCOR E6 have a soft, almost invisible film that is easily removed using mild cleaners.

Environmental approvals are simplified because NOCOR E6 is nitrite, barium, boron, phenol, and phosphate free

NOCOR E6 is low foaming, for use in low-pressure spray washers and flow coating operations. Dip application is also a good way to apply this product

An excellent choice where both ferrous and/or copper alloy parts are being processed

NOCOR E6 has a moderate pH, is practically odorless, and is nonflammable for improved safety

Working concentration ranges from 4% - 16% which translates into much lower cost than traditional straight oil/solvent products

Water-soluble Corrosion Inhibitor

Master STAGES™ NOCOR S2 is a synthetic, water soluble, ferrous corrosion inhibitor for short-term storage or shipment. Effective at concentrations from 3% - 10% in water, it provides a very thin, water-soluble protective film.

The transparent film left by NOCOR S2 is easily removed and will not interfere with additional machining, gauging, or assembly steps

Barium free and contains very low levels of volatile organic compounds as applied

Mild Alkaline Detergent

Master STAGES™ RINSE 100 is a washing compound concentrate that does a great job of removing metalworking fluids and light oily films. This product will not stain ferrous or nonferrous materials and leaves an extremely thin film corrosion inhibitor, which does not interfere with gauging of parts. RINSE 100 is compatible with the TRIM family of cutting and grinding fluid concentrates.

Effective machine cleaner

Great for general cleaning of loose tools and parts

Excellent for use in ultrasonic cleaner systems and immersion washers

Provides up to one week or more of in-process corrosion inhibition on ferrous parts

Long-term Corrosion Inhibitor
On-request only. Contact Customer Service for quotes.

Master STAGES™ RPO 12 is a long-term, indoor rust preventative with a soft waxy film. RPO 12 is compatible with all metals and can be applied by dip, spray, or brush-on methods. The film thickness will be approximately eight microns.

Nonstaining

Humidity Cabinet Test: No rust @ 1400 hours (ASTM D1748)

Salt Spray Test: No rust @ 168 hr. (ASTM B117)

Rust Preventative Oil

Master STAGES™ RPO 6F is a nonstaining, water displacing, thin film rust preventative which can be used on a variety of metals. Provides indoor rust inhibition and excellent protection for bearings, precision parts, and in-process parts during storage and in transit. RPO 6F can be also used as water displacing cleaner and rust preventative.

Excellent rust inhibition

Nonstaining

Provides cleaning action

Water displacing to help prevent rust due to water trapped under the protective film

Easily removed with detergent cleaners

Humidity Cabinet Test: B at 820 hours (GB/T2361)

Salt Spray Test: B at 48 hours (SH/T0081)

Machine Tool Sump and System Cleaner

Master STAGES™ Whamex™ is a safe, fast-acting concentrated formula that will save machine cleaning downtime while removing the oily residues, scums, and insoluble soap deposits that reduce coolant life. Whamex is made for cleaning out machine tool sumps and larger systems, coolant supply lines, and coolant recycling equipment. Whamex is compatible with most waste treatment (including ultrafiltration) and will not degrade TRIM metalworking fluids when used as directed.

A very specialized formula that draws many years of hands-on experience in machine clean outs

Quickly breaks down and lifts off insoluble scum deposits hidden in lines and difficult to reach areas — getting rid of these residues is one of the best ways to extend coolant life in your system

Very hard water tolerant allowing it to be effective in raw water or used coolant

Environmental approvals are simplified because Whamex contains no nitrites, phosphates, barium, phenols, or butyl cellusolve; this formula has very low V.O.C. content and no SARA 313 reportable ingredients

When used as directed below, this product is compatible with TRIM brand semisynthetic and soluble oil coolants, as well as most competitive coolants. Will remove heavy soils from machines without affecting paints, coatings, seals, hoses, or skirting, and it won't leave a slippery residue

Short-term corrosion inhibitors prevent flash rusting of machine surfaces and ways

Low-foam Machine Tool Sump and System Cleaner

Master STAGES™ Whamex XT™ is a low foam, safe, fast-acting, concentrated formula that will save machine cleaning downtime while removing the oily residues, scums, and insoluble soap deposits that reduce coolant life. Whamex XT is made for cleaning out machine tool sumps and larger systems, coolant supply lines, and coolant recycling equipment. Whamex XT is compatible with most waste treatment (including ultrafiltration) and will not degrade TRIM metalworking fluids when used as directed.

A very specialized formula that draws on many years of hands-on experience in machine cleanouts

Quickly breaks down and lifts off insoluble scum deposits hidden in lines and difficult to reach areas — getting rid of these residues is one of the best ways to extend coolant life in your system

Very hard water tolerant allowing it to be effective in raw water or used coolant

Environmental approvals are simplified because Whamex XT contains no nitrites, phosphates, barium, phenols, or butyl cellosolve; this formula has very low V.O.C. content and no SARA 313 reportable ingredients

When used as directed below, this product is compatible with TRIM brand synthetic, semisynthetic, and soluble oil coolants, as well as, most competitive coolants. Will remove heavy soils from machines without affecting paints, coatings, seals, hoses, or skirting, and it won't leave a slippery residue

Short-term corrosion inhibitors prevent flash rusting of machine surfaces and ways

The ultimate coalescing unit for use with large sumps and/or a large number of machine tools

Features

• cast iron self-priming pump
• double-diaphragm air pump with pre-pump strainer
• 264 square feet of removable oleophylic media for maximum oil removal
• includes casters for mobility
• push handle and hose/bucket hangers
• includes tank drain valve for cleaning
• adjustable oil removal weir pipe
• lid on tank

Options

• larger and/or stainless steel tanks
• 110 volt, 50 Hz or 220 volt, 50 Hz operation
• special units for parts washers

Specifications and Utilities

• Process Rate: 1 to 3 GPM (4 to 12 LPM)
• Dimension: 41" l x 19" w x 43" h (1041 mm x 483 mm x 1092 mm)
• Electric: 110 volt, single phase, 60 HZ
• Air: 30 psi/min., 100 psi max

Effectively Remove Oil from Coolants and Washing Solutions

Tramp oil is a major source of problems associated with water miscible cutting and grinding fluids.

Tramp oil contributes to the growth and formation of:

• coolant-destroying bacteria
• undesirable residues on machine tools and workpieces
• smoke and oil mist in shop atmospheres

These problems result in:

• shortened coolant life
• poor material removal rates
• poor surface finish and size control
• decreased tool and wheel life

Numerous devices ("floating ropes," wheels, and belts) have been developed over the years to remove "free floating" tramp oil from the surface of coolant. While they have all worked to one degree or another, they generally have been either "troublesome," high maintenance, relatively ineffective, or able to operate only on limited liquid level fluctuations.

As a "belt-type" skimmer, these units are effective in removing floating oil from widely fluctuating liquid levels of coolants or parts washing solutions. The SCROUNGER features a revolutionary new oleophilic belt and a totally new concept of stripping the separated oil from the belt. The SCROUNGER Jr. uses the same "oil loving" belt, but uses a more compact scraper blade to strip the separated oil from the belt.

Features

• 115 volt, single phase, 50/60 Hz
• heavy-duty, impedence-protected, fan-cooled drive motor with hardened shaft and needle bearings (220 volt, single phase, 50 Hz also available)
• open, accessible oil-collecting tray with a convenient drain connector
• "oil loving" oleophilic belt (purchased separately)
• heavy-duty steel construction, with industrial-grade enamel paint

Benefits

• fast, simple belt changing
• low maintenance
• lower hang roller that will not fall off in the machine sump even in turbulent conditions

Options

• dewatering tray
• portable kit
• special length belts available on special order
• special belt materials available for high temperature or pH applications on special order

SCROUNGER Jr Belts

• all belts 1" [25mm] wide
• 24" [610mm]
• 32" [815mm]
• 44" [1120mm]

Effectively Remove Oil from Coolants and Washing Solutions

Tramp oil is a major source of problems associated with water miscible cutting and grinding fluids.

Tramp oil contributes to the growth and formation of:

• coolant-destroying bacteria
• undesirable residues on machine tools and workpieces
• smoke and oil mist in shop atmospheres

These problems result in:

• shortened coolant life
• poor material removal rates
• poor surface finish and size control
• decreased tool and wheel life

Numerous devices ("floating ropes," wheels, and belts) have been developed over the years to remove "free floating" tramp oil from the surface of coolant. While they have all worked to one degree or another, they generally have been either "troublesome," high maintenance, relatively ineffective, or able to operate only on limited liquid level fluctuations.

As a "belt-type" skimmer, these units are effective in removing floating oil from widely fluctuating liquid levels of coolants or parts washing solutions. The SCROUNGER features a revolutionary new oleophilic belt and a totally new concept of stripping the separated oil from the belt. The SCROUNGER Jr. uses the same "oil loving" belt, but uses a more compact scraper blade to strip the separated oil from the belt.

Features

• 115 volt, single phase, 50/60 Hz
• heavy-duty, impedence-protected, fan-cooled drive motor with hardened shaft and needle bearings (220 volt, single phase, 50 Hz also available)
• open, accessible oil-collecting tray with a convenient drain connector
• "oil loving" oleophilic belt (purchased separately)
• heavy-duty steel construction, with industrial-grade enamel paint

Benefits

• fast, simple belt changing
• low maintenance
• lower hang roller that will not fall off in the machine sump even in turbulent conditions

Options

• dewatering tray
• portable kit
• special length belts available on special order
• special belt materials available for high temperature or pH applications on special order

SCROUNGER Belts (purchased separately)

• all belts 3" [76mm] wide
• two foot hang: total length 70" [1780mm]
• three foot hang: total length 94" [2390mm]
• four foot hang: total length 118" [3000mm]
• six foot hang: total length 166" [4220mm]

Portable Centrifuge Unit for Removing Emulsified Tramp Oils

Developed to meet the needs of the small metalworking plant for a compact, portable, high-speed centrifuge, tramp oil separator, the Tramp Oil Terminator™ will process both water-miscible coolants and aqueous cleaners to remove free and emulsified tramp oils, providing clean and reusable coolants and cleaners. Removing tramp oils (hydraulic oils, way lubes or any undesirable oil) from coolants and cleaners removes a food source for bacteria, reduces undesirable residues, and reduces smoke and oil mist in the shop atmosphere.

Benefits

• Extended life of coolants and cleaners
• Improved machining
• Longer tool life

Features

• Compact and portable for machine tool sumps and parts washers
• Simple operation
• High-speed, disc-bowl centrifuge
• Stainless-steel hood and bowl
• Built-in clean fluid centripetal discharge pump
• Easy dismantling of bowl for cleaning
• Quick disconnects on feed and discharge
• Strainer and 50 micron cleanable pre-filter
• Air pump and floating skimmer for feed
• Automatic shut off when tramp oil collection tank is full

Positive Displacement Proportioners

The UNIMIX™ is a water-driven, positive displacement proportioner, which dispenses coolant on demand at the desired concentration. Special units are availible for alkaline parts washing fluids.

Benefits

• Concentration control
• Reduces concentrate waste
• Easy to install
• Reliable and consistent
• Nonelectrical
• Adjustable

Water Flow Rate

• 5.0 US gpm (19 lpm) noted average flow rate

Mixture Range

• 8 oz. E.M. 1% to 4%
• 16 oz. S.S. 1% to 8%
• 32 oz. X.L. 2%; to 15%

Special UNIMIX for Cleaners

• UNIMIX™ EMC 1% to 6% (up to 12pH)
• UNIMIX™ pH 1% to 6% (up to 14pH)

Chip & Sludge Remover

A perfect match-up with the PurifierPlus is the XYBEX ChipOut. It is also a compact, easy-to-use, affordable solution for optimizing production. It simply and effectively sucks out the coolant, chips, and swarf to collect and filter all solid impurities and return clean coolant to the tank.

Get the most from your coolant with ChipOut. It literally pays for itself in no time with significant cost savings.

XYBEX ChipOut

• Separates surface debris, bottom chips and swarf, and sediment from coolant
• Extends coolant life
• Improves surface finish on parts
• Reduces maintenance
• Uses diaphram pump air pressure, no electricity required
• High suction power, flow rate of 180 liters/min
• Runs during production without shutting off machine tools
• Adjustable stainless steel filters: standard mesh 380 microns; optional: 830 microns and 180 microns
• Optional floating device for maximum tramp oil collection
• Portable and easy to use with multiple machines
• Operates with water-soluble coolants or neet oils

Cost effective ChipOut adds up to big savings

• Reduces annual coolant cost
• Reduces expensive parts rejects
• Reduces maintenance to a minimum

Magnetic Centrifugal Sludge & Chip Remover

Looking for a fast, affordable way to have longer coolant life, reduce maintenance, and achieve better machinability and surface finish? Hardworking ChipOut Plus delivers all that and more in a compact, portable system that can hook up to machines throughout the shop.

It does double time, as both a centrifugal and magnetic separator for water-based cutting fluids or neat oils. It’s simple to use, powerful, and efficient.

First, the suction hose draws in the liquid and impurities. The filtration bucket traps large impurities before the sludge-containing fluid enters the centrifugal separator where fine particles are separated out by centrifugal force. The sludge then enters the powerful magnetic separator which efficiently removes magnetic metallic shavings and particles. Just like its name implies, it takes out chips - plus more!

XYBEX ChipOut Plus

• Separates surface debris, magnetic dust and shavings, chips, swarf, and sediment from coolant
• Extends coolant life
• Improves surface finish on parts
• Reduces maintenance
• Separates using centrifugal and magnetic force
• Provides extremely fine filtration
• No need to stop the machine
• Quick filtration, easy to operate
• Portable, use with multiple machines
• No consumables needed

Use hardworking, cost effective ChipOut Plus to reduce costs and build profits
Save time and build up profits with ChipOut Plus.

• Reduces annual coolant cost
• Reduces maintenance and manpower
• Reduces costly parts rejects

Cutting Fluid Purifying System

The portable, cost-effective XYBEX PurifierPlus system pays for itself with material cost savings, reduced downtime and recycling costs. Not only does it enhance production and make the workplace cleaner, it also is better for employee health and the environment.

Unlike units which simply separate machine tramp oil (the unwanted byproduct of the machining/metalworking process) from coolant, PurifierPlus has an ozone disinfection function which kills bacteria. Not only is the coolant cleaned and lasts longer, it’s purified and reused, and the subsequent problematic stench from bacteria and fungal growth is eliminated.

Improve production, reduce costs, and experience a cleaner workplace with PurifierPlus.

XYBEX PurifierPlus

• Separates free tramp oil and extends coolant life
• Reduces tool wear and costly parts rejects
• Easy to use with a handy set-timer to operate on its own
• Adjustable flow rate filter from 10 to 30 liters/hr
• Kills bacteria (for best results run 1 hour for each 100 liters in sump; ozone function disinfects at 500 mg/hr)
• Built-in pH detector (optional) adjusts pH to control range
• Portable for use on multiple machines in the facility

PurifierPlus quickly pays for itself in savings

• Saves 10% to 25% on annual coolant cost
• Saves 30% to 50% on additional water cost
• Saves 10% to 25% on tooling costs and part reworks
• Reduces clean-up time 60% to 80% annually

The XYBEX System 1000 is a complete, full capability single product coolant recycling system for the medium-sized metalworking plant operation with machine tools fitted with their own coolant sumps.

Application

• For plants operating with one coolant and total sump capacities not exceeding 5,000 U.S. gallons (18,900 liters)

Features

• Small foot print – features over/under tank design
• 300 gallon (1140 liters) dirty coolant tank
• 450 gallon (1700 liters) clean coolant tank
• UNIMIX™>automatic coolant proportioning pump for coolant makeup and concentration control
• High-speed, disc-bowl, liquid-from-liquid centrifuge to clean coolant to less than 0.5% emulsified tramp oil and 2-5 microns of particulate matter
• SCROUNGERoil belt skimmer for removal of free floating, nonemulsified tramp oil
• Automatic operation

The Yellow Bellied Sump Sucker™ will clean virtually any machine tool sump quickly and thoroughly. During the process of cleaning the machine, the sump cleaner also:

• Removes the coolant, sludge and chips from the sump
• Filters the sludge and chips from the coolant
• Returns the filtered coolant to the sump, or transports the coolant to waste treatment for disposal or to a XYBEX Recycling System

The Yellow Bellied Sump Sucker is fast! In a typical example, a cylindrical grinder sump with 120 U.S. gallons (454 liters) of coolant and 700 pounds (318 kilograms) of sludge was completely cleaned, the coolant filtered, and returned to the sump in ten minutes.

Features

• Capacities from 65 U.S. gallons (246 liters) to 1,000 U.S. gallons (3780 liters)
• Single or twin compartment configuration
• Push around, tow around, or truck mounted units available
• 3.5 ft³ (.095m³) or 5.3 ft³ (.14m³) holding capacity sludge basket
• Air, 110V single phase, 3-phase electric, or LP gas power sources
• Complete with hoses and cleaning tools