New Products

WEDOLiT AS 6115 is a modern formulated corrosion inhibitor for steel and other metals. It offers protection for short overseas transport. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfills all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV).

• Suitable for short overseas transport
• VCI films suitable: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed, especially before packing in boxes with film
• Stable against acidic and alkaline impurities
• Good material compatibility
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Water displacing with very good wetting behaviour
• Additive loss due to water contact: Extremely low

WEDOLIT AW 5700 is a water-soluble passivating agent for steel, which is also suitable for ultrasonic and hydro testing systems.

• Almost free of foam and therefore suitable for high speed systems
• Offers a short-term corrosion protection for indoor storage
• Very good skin compatibility
• Contains a special inhibit for copper and brass (for protection of fittings and testing equipment)

WEDOLiT FN 1430-220 is a high viscous, water-insoluble lubricant for tube drawing and other cold forming operations of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners
• Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface, therefore, no preliminary degreasing is necessary before a potential soft annealing

TRIM MicroSol 651XT is a high-lubricity, low-foaming, multi-metal, semisynthetic microemulsion coolant. The formula offers the performance of a heavy-duty soluble oil with the cleanliness of a semisynthetic. It provides excellent cooling and mechanical lubricity, along with the machine friendly characteristics you expect from a premium TRIM coolant. An excellent alternative to soluble oils on high-silica aluminium alloys, MicroSol 651XT is compatible with a wide range of materials and operations.

• High lubricity for extended tool life
• Low foaming for today's high-pressure, high-volume coolant delivery systems
• Excellent sump life without the use of tank side additives
• Provides superior corrosion inhibition on all ferrous and nonferrous metals
• Hard water stable
• Forms a tight microemulsion for low carryoff
• Compatible with a wide range of materials and operations
• Uses standard metalworking recycling and disposal techniques

TRIM SC417 is a cost effective, semisynthetic coolant specifically formulated for machining and grinding of cast iron and steel. This formulation achieves the highest levels of ferrous rust protection whilst also maintaining low levels of foam even in soft water areas. This clean running formulation also prevents the loading of grinding wheels, ensuring good surface finishes and minimal burning.

• Extremely good product for cast iron and steel machining and grinding
• A very versatile product that works well in a wide range of operations such as grinding, milling, turning, drilling and tapping
• Extremely fine emulsion reduces carry-off for low total operating cost
• Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention
• Extremely hard water tolerant
• Easily recycled or disposed of without special handling or equipment

TRIM E730 is a boron-free, high quality, universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems. It has broad application in machining and grinding on a wide range of materials. The high levels of both chemical and mechanical lubricity in this product handle the medium to high duty machining and grinding jobs. The stable and predictable performance of TRIM E730 makes it a first choice for high-quality, consistent parts manufacturing.

• Very stable formula provides long operational life with consistent performance
• Extremely hard water tolerant
• Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE)
• Extremely fine soluble oil emulsion reduces carryoff for low total operating cost
• Fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior corrosion prevention
• Suitable for machining aluminium alloys, steel alloys, nickel alloys, cast iron and yellow metals
• Easily recycled or disposed of without special handling or equipment
• Will run effectively for long periods without the need for costly additives

WEDOLiT N 22-4 is a medium-viscosity, non-water-soluble forming oil for deep-drawing sheet steel, for example, for the automotive industry. This includes sheet metal that is galvanized, or hot-dip galvanized on one or both sides, sheet metal coated with zinc metal, aluminized sheet metal, or sheets made of aluminum or aluminum alloys.

The product meets the requirements of the test procedure according to VDA 230-213, and has been approved by all VDA members.

• Also acts as an anti-corrosion oil
• Subsequent preservation of drawn parts is not necessary due to the good corrosion protection
• Can be applied by spraying, flooding, brushing or with felt rollers
• The oil film can be easily removed with organic solvents or water-soluble alkaline cleaners

WEDOLiT FS 7400 is a non-water-miscible, evaporating calibration oil for light to medium calibration processes.

• Can be applied by dipping or spraying
• The residues left on the surfaces after calibration evaporate completely during annealing

WEDOLiT AN 6999 is a modern formulated corrosion inhibitor for steel and other metals. It offers long-term corrosion protection (indoor storage and potentially outdoor storage) and can be applied by brushes or by means of rollers.

• Ideal for overseas transport
• Suitable for VCI-foils
• Good protection for outdoor storage
• Stable against acidic and alkaline contamination
• Good material compatibility
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Ideal for covered storage
• Offers protection against atmospheric contamination, e.g. dissolved gases that cannot penetrate the protecting film (water vapour permeability)

WEDOLiT CN 3650-13 is a mineral oil based cutting oil for the manufacturing (especially deep-hole drilling) of steel and aluminium alloys. The product contains a combination of EP- and AW-additives, which increase the cutting performance significantly.

• High performance product, which leads to an excellent surface finish and dimensional accuracy
• Highly reduced oil mist formation
• Reduces friction and wear and thus contributes to a high tool life
• Offers high cooling properties with a very good wetting behaviour
• Very good flushing behaviour with an optimal transport of chips and swarf
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT CN 8250-2 is a volatilizing high-performance lubricant, designed for use in all types of low and minimum quantity lubrication systems for milling, sawing, thread cutting and cold forming applications of non-ferrous metals

• High pressure absorption capacity as well as excellent wetting and lubricating effect
• No gumming and sticking
• Reduces build-up of material on steels with a low carbon content
• The excellent cooling and lubricating properties lead to a significant increase in service life of tools and to high dimensional accuracy of workpieces
• Ensures extremely economical use
• Can be easily and safely removed by spray, immersion and ultrasonic cleaning with neutral or alkaline industrial cleaners or with organic solvents

WEDOLiT CN 8471-36 is an ester-based high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems, e.g. for milling, sawing or thread forming, of steel, aluminium and non-ferrous metals.

• Stable load carrying capacity and a homogenous sliding behaviour
• Very good wetting ability and film formation without adhesion
• The outstanding cooling- and lubrication properties lead to significantly reduced friction and wear and thus contribute to a high tool life
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Economical application
• Very good oxidation stability
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT CN 8570-25 is a liquid, odour-less, water insoluble high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems, e.g. for milling, sawing or thread forming, of steel, aluminium and non-ferrous metals.

• Stable load carrying capacity and a homogenous sliding behaviour
• Very good wetting ability and film formation without adhesion
• The outstanding cooling- and lubrication properties lead to significantly reduced friction and wear and thus contribute to a high tool life
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Economical application
• Almost no mist formation and residues
• Very good oxidation stability
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT EP 320 E is a highly viscous, high-performance, ester-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 540-CM is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 760 is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 760-CM is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT FN 1170-225 is a medium viscous, chlorine containing forming oil for tube drawing and other cold forming operations of steel. The product offers also an excellent performance for precision cutting operations. The undiluted product is usually applied by spraying, brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 1450-850 is a high viscous, water-insoluble lubricant for tube drawing and other cold forming operations of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners
• Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface. Therefore, no preliminary degreasing is necessary before a potential soft annealing

WEDOLiT FN 4455-25 is a low viscous, water-insoluble lubricant for medium to heavy forming operations of steel and non-ferrous metals. A combination of EP additives offers a outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 6870-440 is a high-performance product, which is based on highly refined mineral oils. The product is suitable for heavy forming and machining operations of steel, stainless steel and aluminium (e.g. thread cutting, stamping or deep drawing).

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FW 7650 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

• Due to its thermal stability the product can be used in the whole production line (forming, welding, calibration, sawing)
• No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing

WEDOLiT FW 9114 is a water miscible forming lubricant based on biodegradable natural raw materials. The product is universally applicable in steel forming processes.

The application concentration depends on the level of difficulty of the forming operations and has to be determined in preliminary tests. Concentrations of 10 - 30% are usually recommended.

• Can be applied undiluted as a concentrate
• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Very good material compatibility
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT N 22 NV is a thixotropic water insoluble washing oil for cleaning metal sheets and coils. The product is usually used in washing machines at ambient temperatures. Increasing the temperature to approx. 60 °C enhances the washing effect. The oil film that remains on the surface after the washing process offers sufficient forming properties for medium to heavy forming operations (for cold forming of uncoated and galvanized steel and for and aluminum).

Approved by Volkswagen (VW-Material-Nr. 29.4186) and by Mercedes Benz (Nr. 34/95-10576 VWT).

• Compatible (according to tests and our experience) with all for the automotive industry typical adhesives and paints (KTL)
• Acts as a corrosion protection agent. Therefore, a post-treatment of the drawn sheets is not necessary
• An ageing stable film is formed after drawing
• Can easily be removed with organic solvents or water soluble, mild industrial alkaline cleaning agents, even after long storage periods
• A phosphating can easily be conducted after degreasing

WEDOLiT CW 6506 is suitable for light to heavy cutting operations of steel, stainless steel, aluminium (e.g. sensitive aluminium alloys of the 2000 and 7000 series) and non-ferrous metals.

WEDOLiT CW 6506 is approved by CETIM according to specification EADS ASN 42302 annex 2, DASSAULT DQGT 0.4.2.0065 index D and by Bombardier BAMS 569-001 rev. B, for the aerospace industry.

• Offers high cooling- and flushing properties with a very good wetting behaviour
• Contributes to a high tool life
• Very good application stability
• Almost free of foam
• Offers a very good skin compatibility

WEDOLiT FN 1430-115 is a medium viscous, water-insoluble lubricant for tube drawing and other cold forming operations of non-ferrous metals. The undiluted product is usually applied by spraying, brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners
• Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface, therefore, no preliminary degreasing is necessary before a potential soft annealing

WEDOLiT FN 1872-50 is a water-insoluble, reactive drawing oil, based on special phosphoric acid esters, which creates an iron phosphate layer on iron and steel parts. The product is free of chlorine, sulphur or nitrites.

• The product is used in a heated bath with a temperature of T_Bath = 60°C ± 5°C
• After 10 - 15 min, a sufficient film should have been developed on the tube surface (residues of lime- or carbon deposits must be removed preliminary)
• It is important to keep the water content in the product at a value of 1 - 1.7%, to form uniform phosphate layers on the tube surface
• The product offers a short-term corrosion protection (max. a few days)
• The pipes can be cleaned after drawing with alkaline cleaners, solvents or bright annealing

WEDOLiT FW 6550-165 is a synthetic, mineral oil and chlorine-free, highly additivated punching and forming medium. The EP additives ensure a pressure-resistant lubricating film, even in difficult machining processes.

• Suitable for deep-drawing, extrusion, punching and cutting processes not only on steels, but also on stainless steels
• Undiluted by brush or felt roller and can be easily washed off with water
• Does not contain any insoluble pigments such as graphite or molybdenum disulfide