Forming - Water Miscible Fluids

WEDOLiT FW 1960 is a water-soluble alkaline soap for heavy drawing operations of steel tubes. The product is usually used as an immersion bath (bath temperature 75 – 90°C).

• The product is designed to react with the zinc phosphate layer (which acts as lubricant) to form a zinc soap. The zinc phosphate layer should be at least 4 μm (at heavy forming operations, e.g. cold extrusion, up to 10 μm). Due to specific additives, a maximum conversion of zinc phosphate and the drawing media occurs, which results in an optimal performance regarding degree and rate of deformation
• Can be used in very low concentrations of 5 - 10% as an aqueous solution (tube drawing). The best results are obtained with water free media
• Offers (in combination with a zinc phosphate layer) very high cross-sectional reduction and high drawing velocities – up to 100 m/min (steel tubes with standard cross-sectional reduction)

WEDOLiT FW 3500 is a high-pressure agent for hydroforming-processes such as internal and external high pressure forming of steel plates, with different surface qualities and thicknesses. The product can also be applied in different grinding and cooling operations.

Approved by “FF Fluid Forming“

• Offers very good high-pressure properties
• Contributes to a high tool life
• Very good application stability
• Almost free of foam
• Offers very good skin compatibility


Recommended mixing ratio
• Hydrofroming:  from 5 - 10%
• Grinding:  from 3 - 6%

WEDOLiT FW 6550-165 is a synthetic, mineral oil and chlorine-free, highly additivated punching and forming medium. The EP additives ensure a pressure-resistant lubricating film, even in difficult machining processes.

• Suitable for deep-drawing, extrusion, punching and cutting processes not only on steels, but also on stainless steels
• Undiluted by brush or felt roller and can be easily washed off with water
• Does not contain any insoluble pigments such as graphite or molybdenum disulfide

WEDOLiT C 142 is primarily used for manufacturing steel pipes on pipe welding machines and as a press water additive, and is also suitable for galvanized materials.

• The requirements for cleanliness of the rollers and pipes are met
• Due to its temperature stability, it can also be used in the water cooling section for the weld seam, in addition to cooling the electrode or for high-frequency welding of coils and impeders
• The entire pipe welding machine is thus operated with a closed cooling lubrication system without external water supply
• Has no emulsifying effect on mineral oils and machine lubricants
• This makes it possible to use rust protection oil on the turret head of pipe welding machines in the manufacture of profile pipes
• Metal abrasion can be easily removed without clogging the filters. Foreign oils introduced as leak oil can be centrifuged without loss of active ingredients
• Can be easily removed with organic solvents and alkaline cleaners

WEDOLiT FW 7650 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

• Due to its thermal stability the product can be used in the whole production line (forming, welding, calibration, sawing)
• No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing

WEDOLiT FW 7651 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

• Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
• No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing


Recommended mixing ratio
• Tube welding:  from 4 - 6%

WEDOLiT FW 7652 is suitable for wire drawing as well as for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

• Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
• No emulsification of mineral oils and engine lubricants. Therefore, the application of a corrosion inhibition oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing


Recommended mixing ratio
• Tube welding:  from 4 - 6%
• Wire drawing:  from 3 - 12%

WEDOLiT FW 7661 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 3 - 5%).

• Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
• No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacturing of profiled tubes)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing


Recommended mixing ratio
• Tube welding:  3 -5%

WEDOLiT FW 7840 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration from 7%).

The product is approved by Mercedes-Benz Group AG (formerly Daimler AG) (QSO 040305) under the name WEDOLiT K 911.

• Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing


Recommended mixing ratio
• Tube welding:  from 7%

WEDOLiT FW 9114 is a water miscible forming lubricant based on biodegradable natural raw materials. The product is universally applicable in steel forming processes.

The application concentration depends on the level of difficulty of the forming operations and has to be determined in preliminary tests. Concentrations of 10 - 30% are usually recommended.

• Can be applied undiluted as a concentrate
• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Very good material compatibility
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FW 9200 is an ester-based, water-miscible forming lubricant, which can be universally applied in forming (especially drawing) processes of brass and non-ferrous metals.

The application concentration depends on the level of difficulty of the forming operations and has to be determined in preliminary tests. Concentrations of 10 - 15% are usually recommended.

• Can be applied undiluted as a concentrate
• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• Very good material compatibility
• Easily removable with organic solvents or alkaline industrial cleaners


Recommended mixing ratio
• Drawing operations:  10 - 15%

WEDOLiT FW 9900 is a water-miscible, ester based forming lubricant (soap) that can be used universally for deep drawing and other forming operations of brass. The concentration depends on the level of difficulty of the forming operation and should be determined in preliminary tests (usually in the range between 10 - 15%). The product can also be used undiluted.

• Outstanding performance
• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners