WEDOLiT

WEDOLiT AE 1030 is a dewatering fluid based on the latest ester technology that uses surface-active substances to displace both water and emulsions from the metal surface quickly. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

Not subject to the German solvent guideline VOC 31. BImSCHV or to the Swiss regulation concerning the incentive tax on volatile solvents (VOCV). Fulfils all requirements regarding ELV 2000/53/EG.

• Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
• Water/emulsions that enter the bath will settle on the bottom of the tank after a short period and can be drained off
• Development of a clear phase boundary between the water and the product, without forming an emulsion phase
• Excellent bath-life
• Additive loss due to water contact: None

WEDOLiT AN 4240 is a modern formulated corrosion inhibitor for steel and other metals, which develops a slightly greasy film. The resulting film consists of natural corrosion protection additives with a specific odour. It offers a long-term corrosion protection (indoor storage) and can be applied by spraying, flooding or by means of rollers. A homogenisation before usage is recommended.

Fulfills all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) as well as to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

• Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed, especially before packing in boxes with foils
• Stable against acidic and alkaline contamination
• Good material compatibility
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Ideal for covered storage
• Offers protection against atmospheric contamination, e.g. dissolved gases which cannot penetrate the protecting film (water vapour permeability)

WEDOLiT AN-5200 is a modern formulated corrosion inhibitor for steel and other metals. It offers protection for a short storage period and is suitable for light straightening processes. It can be applied by spraying, flooding or by means of rollers.

Fulfills all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) as well as to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

• Suitable for VCI-foils
• Stable against acidic and alkaline contamination
• Good material compatibility
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

WEDOLiT AN 6111 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

• Ideal compatibility with VCI-foils
• Stable against acidic and alkaline contamination
• Good material compatibility
• Water displacing with very good wetting behaviour
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Additive loss due to water contact: Low

WEDOLiT AN 6112 is a dewatering fluid with corrosion protection properties that uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can efficiently be dewatered. It is mainly used as an immersion bath at room temperature.

Fulfills all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31 BImSchV) as well as to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

• Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
• Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
• Development of a clear phase boundary between the water and the product, without forming an emulsion phase
• Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
• Excellent bath-life
• Additive loss due to water contact: Extremely low

WEDOLiT AN 6210 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow bodies. It can also be applied by spraying, flooding or by means of rollers. Due to the high oil content, it can also be used as a straightening oil.

Fulfills all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) as well as to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

• Ideal for overseas transport
• Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
• Can be used as a straightening oil or for light forming operations
• Stable against acidic and alkaline contamination
• Excellent bath life
• Excellent material compatibility
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Additive loss due to water contact: Extremely low

WEDOLiT AN-7114 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

WEDOLiT AN-7114 fulfills all requirements regarding Altautorichtlinie 2000/53/EG. It is not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

• Ideal compatibility with VCI-foils
• Stable against acidic and alkaline contamination
• Good material compatibility
• Water displacing with very good wetting behaviour
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Additive loss due to water contact: Low

WEDOLiT AN 7121 is a modern formulated corrosion inhibitor for steel and other metals, which develops a slightly greasy film. The resulting film consists of natural corrosion protection additives with a specific odour. It offers a long-term corrosion protection (indoor storage) and can be applied by spraying, flooding or rolling. Homogenisation before usage is recommended.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

• Ideal for VCI-foils
• Stable against acidic and alkaline contamination
• Good material compatibility
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Ideal for covered storage
• Offers protection against atmospheric contamination, e.g. dissolved gases which cannot penetrate the protecting film (water vapour permeability)

WEDOLiT AN 7210 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) nor to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

• Suitable for overseas transport
• Ideal compatibility with VCI-foils
• Stable against acidic and alkaline contamination
• Good material compatibility
• Water displacing with very good wetting behaviour
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Additive loss due to water contact: Low

WEDOLiT AS 1012 is a dewatering fluid with corrosion protection properties. It uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can efficiently be dewatered. It is mainly used as an immersion bath at room temperature.

• Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions or synthetic coolants are removed from the metal surface
• After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
• Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
• Development of a clear phase boundary between the water and the product, without forming an emulsion phase
• Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
• Excellent bath-life
• Additive loss due to water contact: None

WEDOLiT AS 1211 is a dewatering fluid with a corrosion protection that uses surface-active substances to displace both water and emulsions from the metal surface extremely quickly. Even highly complex geometries can be quickly and efficiently dewatered. It is mainly used as an immersion bath at room temperature.

The product is approved by Mercedes-Benz Group AG (formerly Daimler AG) (QSO 040212) under the name K 722.

• Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
• After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
• Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
• Development of a clear phase boundary between the water and the product, without forming an emulsion phase
• Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
• Excellent bath-life
• Additive loss due to water contact: None

WEDOLIiT AS 1723 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited period of outdoor storage. It can be applied by spraying, flooding, brushing or by means of rollers.

• Ideal for overseas transport
• Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
• After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface
• Good protection for outdoor storage
• It´s recommended to homogenise the product before use or after a longer storage period
• Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)

WEDOLiT AS 2111-CM is a modern formulated corrosion inhibitor for steel and other metals, that offers protection for short overseas transport. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

• Suitable for overseas transport
• VCI films suitable: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed, especially before packing in boxes with film
• Stable against acidic and alkaline impurities
• Good material compatibility
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Water displacing with very good wetting behaviour
• Additive loss due to water contact: Extremely low

WEDOLiT AS-2241 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

• Ideal for overseas transport
• Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
• Stable against acidic and alkaline contamination
• Good material compatibility
• Water displacing with very good wetting behaviour
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Additive loss due to water contact: Extremely low

WEDOLiT AS-2251 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

• Ideal for overseas transport
• Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
• Stable against acidic and alkaline contamination
• Good material compatibility
• Water displacing with very good wetting behaviour
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Additive loss due to water contact: Very low

WEDOLiT AS 2411 is a dewatering fluid with a corrosion protection that uses surface-active substances to displace both water and emulsions from the metal surface extremely quickly. Even highly complex geometries can be quickly and efficiently dewatered. It is mainly used as an immersion bath at room temperature.

• Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
• After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
• Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
• Development of a clear phase boundary between the water and the product, without forming an emulsion phase
• Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
• Excellent bath-life
• Additive loss due to water contact: None

WEDOLiT AS 2603 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited storage period for outdoor storage. It can be applied by spraying, flooding, brushing or by means of rollers.

• Ideal for overseas transport
• Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
• After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface
• Good protection for outdoor storage
• It´s recommended to homogenise the product before use or after a longer storage period
• Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)

WEDOLiT AS 3040 is a dewatering fluid with corrosion protection properties that uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

• Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions and synthetic coolants are removed from the metal surface
• After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
• Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
• Development of a clear phase boundary between the water and the product, without forming an emulsion phase
• Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
• Excellent bath-life
• Additive loss due to water contact: None

WEDOLiT AS 4111 is a leading edge universally applicable, corrosion protection which offers a long-term protection for indoor storage. It has been especially developed for loosening rusted parts and can be applied by spraying, flooding or via an immersion bath.

• Suitable for overseas tranpsort
• Rust remover for humidity-related ignition problems in electrical systems
• Loosens rusted screws, nuts, joints, hinges, switches and mechanisms
• Cleans dirty tools and components and protects them from corrosion
• Stable against acidic and alkaline impurities
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Water displacing with very good wetting behaviour
• Additive loss due to water contact: Low

WEDOLiT AS-4116 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing of rolling.

• Ideal for overseas transport
• Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
• Stable against acidic and alkaline contamination
• Good material compatibility
• Water displacing with very good wetting behaviour
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Additive loss due to water contact: Extremely low

WEDOLiT AS 4116-3 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

• Ideal for overseas transport
• Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
• Stable against acidic and alkaline contamination
• Good material compatibility
• Water displacing with very good wetting behaviour
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Additive loss due to water contact: Very low

WEDOLiT AS 4143 is a dewatering fluid with corrosion protection properties. It uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be efficiently dewatered. It is mainly used as an immersion bath at room temperature.

• Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions and synthetic coolants are removed from the metal surface
• After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage
• Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off
• Development of a clear phase boundary between the water and the product, without forming an emulsion phase
• Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
• Excellent bath-life
• Additive loss due to water contact: None

WEDOLiT AS 4241 is a modern formulated corrosion inhibitor for steel and other metals, which offers long-term protection (indoor storage). Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

• Ideal for overseas transport
• Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils
• Stable against acidic and alkaline contamination
• Good material compatibility
• Water displacing with very good wetting behaviour
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Additive loss due to water contact: Extremely low

WEDOLiT AS 6115 is a modern formulated corrosion inhibitor for steel and other metals. It offers protection for short overseas transport. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding or by means of rollers.

Fulfills all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV).

• Suitable for short overseas transport
• VCI films suitable: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed, especially before packing in boxes with film
• Stable against acidic and alkaline impurities
• Good material compatibility
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners
• Water displacing with very good wetting behaviour
• Additive loss due to water contact: Extremely low

WEDOLIT AW 5700 is a water-soluble passivating agent for steel, which is also suitable for ultrasonic and hydro testing systems.

• Almost free of foam and therefore suitable for high speed systems
• Offers a short-term corrosion protection for indoor storage
• Very good skin compatibility
• Contains a special inhibit for copper and brass (for protection of fittings and testing equipment)

WEDOLiT AW 5801 is a mildly alkaline, sprayable corrosion protection emulsion containing mineral oil, free of boron compounds, suitable for the temporary corrosion protection of workpieces made of steel, iron and cast iron materials.

• The concentrate forms an opaque solution when diluted with water
• Used as a 3 - 6% aqueous solution for the temporary corrosion protection of steel or steel alloys (e.g. for car body parts)
• The applied protective film remains fully water-soluble

WEDOLiT AW 5811 is a water-soluble passivating agent for steel, which is used as an aqueous solution for a short-term corrosion protection. The product contains no oily or fatty substances and is free of sodium nitrite. Furthermore, it contains a copper and brass inhibitor (for the protection of fittings, etc.).

• Almost foam free
• Low electric conductivity
• While the protecting film remains water soluble, the product is suitable as a short-term corrosion protection of steel (covered storage)
• Good skin compatibility

WEDOLiT AW 7101 is a mineral oil-containing, water miscible corrosion protection fluid. The water-mixed emulsion is stable to boiling and electrolytes for a short time. Emulsifiers, inhibitors and high-pressure additives are combined to be used for different applications in both metalworking and corrosion protection with just one product.

Due to its low foam formation at high temperatures, WEDOLiT AW 7101 is also suitable for use as a rinsing emulsion in the production of fixed pipes. The pipes must be dried before packing to avoid condensation water corrosion

• free of boron
• insensitive to short-term thermal overheating
• low foaming even at higher emulsion temperatures

WEDOLiT CN 2370-7 is a low viscous, high performance grinding oil based on the latest gas to liquid (GTL) technology. GTL-base-oils are free of aromatics, chlorine, zinc, nitrogen and heavy metals, to provide the best occupational safety for the worker. The product is suitable for the machining of HSS and carbides (especially with a high cobalt content). The product is also suitable for general cutting operations as well as for gear hobbing.

• High performance product, which leads to an excellent surface finish and dimensional accuracy
• Highly reduced oil mist formation, almost no loss of evaporation
• Reduces friction and wear and thus contributes to a long tool life
• Offers high cooling properties with a very good wetting behaviour
• Very good flushing behaviour with an optimal transport of chips and swarf
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT CN 3650-13 is a mineral oil based cutting oil for the manufacturing (especially deep-hole drilling) of steel and aluminium alloys. The product contains a combination of EP- and AW-additives, which increase the cutting performance significantly.

• High performance product, which leads to an excellent surface finish and dimensional accuracy
• Highly reduced oil mist formation
• Reduces friction and wear and thus contributes to a high tool life
• Offers high cooling properties with a very good wetting behaviour
• Very good flushing behaviour with an optimal transport of chips and swarf
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT CN 5370-12 is a low-viscosity, non-water soluble high-performance cutting oil based on high performance paraffinic base oil technology, which was developed for thread cutting operations. The product is also suitable for general cutting operations of high alloyed steels, cast iron, aluminium and non-ferrous metals.

• High performance product, which leads to an excellent surface finish and dimensional accuracy
• Special additivation for thread cutting operations
• Highly reduced oil mist formation, almost no loss of evaporation
• Reduces friction and wear and thus contributes to a high tool life
• Offers high cooling properties with a very good wetting behaviour
• Very good flushing behaviour with an optimal transport of chips and swarf
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT CN 5370-22 is a low viscous, non-water soluble, high performance cutting oil for thread cutting operations, which is based on the latest base-oil-technology. The product is also suitable for general cutting operations of high alloyed steels, cast iron, aluminium and non-ferrous metals.

• High performance product, which leads to an excellent surface finish and dimensional accuracy
• Special additivation for thread cutting operations
• Highly reduced oil mist formation, almost no loss of evaporation
• Reduces friction and wear and thus contributes to a long tool life
• Offers high cooling properties with a very good wetting behaviour
• Very good flushing behaviour with an optimal transport of chips and swarf
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT CN 8471-36 is an ester-based high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems, e.g. for milling, sawing or thread forming, of steel, aluminium and non-ferrous metals.

• Stable load carrying capacity and a homogenous sliding behaviour
• Very good wetting ability and film formation without adhesion
• The outstanding cooling- and lubrication properties lead to significantly reduced friction and wear and thus contribute to a high tool life
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Economical application
• Very good oxidation stability
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT CN 8570-25 is a liquid, odour-less, water insoluble high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems, e.g. for milling, sawing or thread forming, of steel, aluminium and non-ferrous metals.

• Stable load carrying capacity and a homogenous sliding behaviour
• Very good wetting ability and film formation without adhesion
• The outstanding cooling- and lubrication properties lead to significantly reduced friction and wear and thus contribute to a high tool life
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Economical application
• Almost no mist formation and residues
• Very good oxidation stability
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT CS 6206 is suitable for grinding of steel, cast iron, aluminium, non-ferrous metals, glass and especially carbides.

• Offers high cooling- and flushing properties with a very good wetting behaviour
• Contributes to a high tool life
• Very good application stability
• Almost free of foam
• Offers a good skin compatibility


Recommended mixing ratio
• Grinding:  from 4%
• General cutting:  from 6%

WEDOLiT CS 8208 is suitable for ultrasonic testing systems. The product is also suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 5 - 10%). Not suitable for the manufacturing of workpieces made of zinc, aluminium and their alloys.

• Offers high cooling- and flushing properties with a very good wetting behaviour
• Contributes to a high tool life
• Very good application stability
• Almost free of foam
• Offers a good skin compatibility
• Due to its thermal stability, the product can be used in almost the whole process chain of welded tubes (forming, welding, calibration, sawing)

WEDOLiT CW 6506 is suitable for light to heavy cutting operations of steel, stainless steel, aluminium (e.g. sensitive aluminium alloys of the 2000 and 7000 series) and non-ferrous metals.

WEDOLiT CW 6506 is approved by CETIM according to specification EADS ASN 42302 annex 2, DASSAULT DQGT 0.4.2.0065 index D and by Bombardier BAMS 569-001 rev. B, for the aerospace industry.

• Offers high cooling- and flushing properties with a very good wetting behaviour
• Contributes to a high tool life
• Very good application stability
• Almost free of foam
• Offers a very good skin compatibility

WEDOLiT CW 8906 is suitable for grinding as well as light to heavy cutting operations of steel, stainless steel, aluminium and titanium.

• Offers high cooling- and flushing properties with a very good wetting behaviour
• Contributes to a high tool life
• Very good application stability
• Almost free of foam
• Offers a very good skin compatibility

WEDOLiT EP 1090 is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilisation in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents the stick-slip- effect due to the high content of polar additives.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 320 E is a highly viscous, high-performance, ester-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 430 ES is a high-performance special oil based on mineral oil esters, developed to the highest technical standards for use in the pipe industry. The product emulsifies spontaneously and contains polar additives to prevent stick slip.

WEDOLiT EP 430 ES is used to lubricate sliding surfaces and guideways of mechanical expanders under extremely high surface pressure in the manufacture of large steel pipes, e.g., for gas and oil pipelines. WEDOLIT EP 430 ES is used undiluted for the forming process. The emulsion can be used for pre- and post-cleaning of the pipes and for cleaning the expander head and can be separated into split water and oily waste with suitable additives. The split water could be reused to prepare the emulsion.

• Very high lubricating film stability under pressure loads
• Good adhesion to smooth surfaces, good wear protection
• Prevents stick slip
• Stable emulsion, easily separable

WEDOLiT EP 435 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 438 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 540 is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 540-CM is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 540 ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and due to the high content of polar additives, prevents the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and expander heads and can be easily separated into water and oily waste by utilising specific additives
• Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 545-E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 760 is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 760 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilisation in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilisation of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 760 ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilisation in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and due to the high content of polar additives, prevents the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by utilising specific additives
• Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 760-CM is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT FN 1170-225 is a medium viscous, chlorine containing forming oil for tube drawing and other cold forming operations of steel. The product offers also an excellent performance for precision cutting operations. The undiluted product is usually applied by spraying, brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 1190-2300 is a highly viscous, chlorine containing forming oil for tube drawing and other cold forming operations of stainless steel. The undiluted product is usually applied by brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners
• Soluble in chlorinated hydrocarbons

WEDOLiT FN 1430-115 is a medium viscous, water-insoluble lubricant for tube drawing and other cold forming operations of non-ferrous metals. The undiluted product is usually applied by spraying, brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners
• Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface, therefore, no preliminary degreasing is necessary before a potential soft annealing

WEDOLiT FN 1430-220 is a high viscous, water-insoluble lubricant for tube drawing and other cold forming operations of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners
• Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface, therefore, no preliminary degreasing is necessary before a potential soft annealing

WEDOLiT FN 1450-850 is a high viscous, water-insoluble lubricant for tube drawing and other cold forming operations of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners
• Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface. Therefore, no preliminary degreasing is necessary before a potential soft annealing

WEDOLIT FN 1490-30 is a low viscous, water-insoluble lubricant for tube drawing and other cold forming operations of aluminium and non-ferrous metals. The undiluted product is usually applied by spraying, brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners
• Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface. Therefore, no preliminary degreasing is necessary before a potential soft annealing

WEDOLiT FN 1530-650 is a highly viscous, non-water soluble lubricant suitable for tube, bar and wire drawing of bright steel. The undiluted product is usually used as a dip or applied by brushes or felt rollers.

• Stable load-bearing capacity and homogeneous sliding properties
• Reliably reduces friction and wear and thus contributes to long tool life
• Excellent wetting and film formation without sticking
• Stable cold start behaviour, prevents stick-slip effect and chattering
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• Can be removed with solvent-based or alkaline cleaners

WEDOLIT is a highly viscous, water-insoluble lubricant for tube drawing and other cold forming processes of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners
• Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface. Therefore, no preliminary degreasing is necessary before a potential soft annealing

WEDOLiT FN 1571-2800 is a highly viscous, water-insoluble lubricant for tube drawing and other cold forming processes of aluminium and non-ferrous metals. The undiluted product is usually applied by brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners
• Evaporates at temperatures T ≥ 300°C without leaving any residues or stains on the metal surface. Therefore, no preliminary degreasing is necessary before a potential soft annealing

WEDOLiT FN 1850-9 is a mineral-oil based, chlorine containing, high performance lubricant for cold forming operations of steel and stainless steel (e.g. tube drawing of very small diameter tubes). The undiluted product can be applied by spraying, brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 1872-50 is a water-insoluble, reactive drawing oil, based on special phosphoric acid esters, which creates an iron phosphate layer on iron and steel parts. The product is free of chlorine, sulphur or nitrites.

• The product is used in a heated bath with a temperature of T_Bath = 60°C ± 5°C
• After 10 - 15 min, a sufficient film should have been developed on the tube surface (residues of lime- or carbon deposits must be removed preliminary)
• It is important to keep the water content in the product at a value of 1 - 1.7%, to form uniform phosphate layers on the tube surface
• The product offers a short-term corrosion protection (max. a few days)
• The pipes can be cleaned after drawing with alkaline cleaners, solvents or bright annealing

WEDOLiT FN 1940-60 is a medium viscous, water-insoluble lubricant for tube drawing and other cold forming operations of steel, aluminium and non-ferrous metals. The undiluted product can be applied by spraying, brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 2451-150 is a medium viscous, water-insoluble lubricant for wire drawing and other cold forming processes, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminium. The undiluted product is usually applied by brushes or rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a long tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 2451-180 is a medium viscous, water-insoluble lubricant for wire drawing and other cold forming operations, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminium. The undiluted product is usually applied by brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 2451-850 is a highly viscous, water-insoluble lubricant for wire drawing and other cold forming processes, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminium. The undiluted product is usually applied by brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 2551-1800 is a highly viscous, water-insoluble lubricant for wire drawing and other cold forming processes, e.g. deep drawing, extrusion or thread forming, of steel, stainless steel and aluminium. The undiluted product is usually applied by brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 4170-35 is a low viscous, water-insoluble chlorinated lubricant for heavy forming operations of steel and stainless steel. A combination of EP additives offers an outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 4455-25 is a low viscous, water-insoluble lubricant for medium to heavy forming operations of steel and non-ferrous metals. A combination of EP additives offers a outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 4455-55 is a low viscous, water-insoluble lubricant for heavy forming operations of steel and non-ferrous metals. A combination of EP additives offers a outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushing or rolling.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a long tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 6160-90 is a water-insoluble, chlorinated lubricant for deep drawing and other cold forming operations, e.g. wire drawing, extrusion or thread forming of steel and stainless steel. The undiluted product is usually applied by flooding, spraying, brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 6870-170 is a medium viscous, water-insoluble lubricant for deep drawing and other cold forming processes of steel (e.g. for auto bodies). Additionally, the product is suitable as a spot lubricant for thread cutting or blind hole drilling. The undiluted product is usually applied by spraying, dipping, brushes or by means of rollers.

The product meets the requirements of the test procedure according to VDA 230-213.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 6870-38 is a water-insoluble lubricant for wire drawing and other cold forming operations, e.g. deep drawing, extrusion or thread forming, of steel and stainless steel. The undiluted product is usually applied by flooding, spraying, brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 6870-440 is a high-performance product, which is based on highly refined mineral oils. The product is suitable for heavy forming and machining operations of steel, stainless steel and aluminium (e.g. thread cutting, stamping or deep drawing).

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FN 8830 is a chlorine free, pasty, water-insoluble lubricant for cold forming processes (e.g. pilgering) of high alloyed steels. The product is usually applied on the outer diameter by brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• The outstanding extreme-pressure properties combined with an exceptional adhesion offers the possibility for high degrees of deformation
• Stable cold start behaviour, prevents stick-slip and chatter
• Contributes to achieving dimensional accuracy
• Pigments will remain on the surface after annealing and need to be removed (e.g. by pickling with HCl or HNO₃) before further processing

WEDOLiT FN 8850-90 is a medium viscous, water-insoluble lubricant for tube drawing and other cold forming operations of steel. Due to the fact that the product also offers corrosion protection, no additional treatment is necessary (for short term storage). The undiluted product is usually applied by spraying, brushes or by means of rollers.

• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FS 3100 is a low viscous, water-insoluble lubricant for stamping and bending operations of steel, aluminium and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushes or by means of rollers.

• Good spreading behaviour, which leads to a uniform wetting of the metal surface
• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Evaporates after a short time without leaving any residue - an additional cleaning process is not necessary

WEDOLiT FS 3310 is a low viscous, water-insoluble lubricant for stamping and bending operations of steel, aluminium and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushing, or rolling.

• Good spreading behaviour which leads to a uniform wetting of the metal surface
• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a long tool life
• Leads to clean surfaces and contributes to dimensional accuracy
• If the product is finely dispersed, it evaporates after a short time without leaving any residues and therefore, an additional cleaning step is not necessary
• It is easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FS 3710 is a non-water soluble, synthetic cooling lubricant of low viscosity. It is applicable for drawing- and punching-operations of aluminium. Can be applied undiluted by spraying, flooding, brushing or rolling.

• Good wetting of the metal surface
• Nearly odourless
• Despite the good lubrication properties, the product is characterised by a quick evaporation and high flash point
• The working area should be sufficiently ventilated, due to the amount of volatile hydrocarbons

WEDOLiT FS 3910 is non-water-soluble cooling lubricant with low viscosity for punching- and bending operations on steel and zinc coated steel. The product is not applicable for the treatment of nonferrous metals.

• Can be applied undiluted by spraying, flooding, brushing or rolling
• Has a good spread effect, which causes an optimal even wettability of metal surfaces
• Has a simultaneously cleaning effect
• Contains a combination of aromatic free solvents with additives of esters and extreme-pressure compounds and is therefore practically odourless
• Is marked by a very fast evaporation with high flash point

WEDOLiT FS 4101 is a low-viscosity, solvent-based lubricant suitable for stamping and bending operations on steel, aluminium and non-ferrous metals. The product is usually applied undiluted by spraying, flooding, brushing or by means of felt rollers.

• Very good spreading effect, resulting in an optimal and uniform wetting of the metal surface
• Stable load-bearing capacity and homogeneous sliding properties
• Reliably reduces friction and wear and thus contributes to long tool life
• Leads to clean surfaces and contributes to the achievement of dimensional accuracy
• If finely applied, the product evaporates after a short time almost without leaving any residue, so that additional cleaning of the workpieces is not necessary. Otherwise, the product can be easily removed with solvent-based or alkaline cleaners

WEDOLiT FS 4311 is a low viscous, water-insoluble lubricant for tube drawing and other cold forming processes of steel, aluminium and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushes or by means of rollers.

• Good spreading behaviour, which leads to a uniform wetting of the metal surface
• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• If the product is finely dispersed, it evaporates after a short time without leaving any residues. Therefore, an additional cleaning step is not necessary, Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FS 4512 is a low-viscosity, solvent-based lubricant suitable for punching and bending operations on steel, aluminum, and non-ferrous metals. The product is usually applied undiluted by spraying, flooding, brushing, or felt rollers.

• Excellent spreading effect, resulting in optimal and uniform wetting of the metal surface
• Stable load-bearing capacity and homogeneous sliding properties
• Reliably reduces friction and wear, thereby contributing to long tool life
• Leads to clean surfaces and contributes to dimensional accuracy
• When finely distributed, the product evaporates almost without residue after a short time, eliminating the need for additional cleaning of the workpieces. Otherwise, the product can be easily removed with solvent-based or alkaline cleaners

WEDOLiT FS 4700 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminium and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushes or by means of rollers.

• Good spreading behaviour, which leads to a uniform wetting of the metal surface
• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Leads to clean surfaces and contributes to achieve dimensional accuracy

WEDOLiT FS 4710 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminium and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushes or by means of rollers.

• Good spreading behaviour, which leads to a uniform wetting of the metal surface
• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• If the product is finely dispersed, it evaporates after a short time without leaving any residue. Therefore, an additional cleaning step is not necessary. Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FS 6311 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminium and non-ferrous metals, which also performs excellently in thread rolling operations (aluminium). The undiluted product is usually applied by spraying, flooding, brushes or by means of rollers.

• Good spreading behaviour, which leads to a uniform wetting of the metal surface
• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• If the product is finely dispersed, it evaporates after a short time without leaving any residues. Therefore, an additional cleaning step is not necessary. Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FS 7400 is a non-water-miscible, evaporating calibration oil for light to medium calibration processes.

• Can be applied by dipping or spraying
• The residues left on the surfaces after calibration evaporate completely during annealing

WEDOLiT FW 1960 is a water-soluble alkaline soap for heavy drawing operations of steel tubes. The product is usually used as an immersion bath (bath temperature 75 – 90°C).

• The product is designed to react with the zinc phosphate layer (which acts as lubricant) to form a zinc soap. The zinc phosphate layer should be at least 4 μm (at heavy forming operations, e.g. cold extrusion, up to 10 μm). Due to specific additives, a maximum conversion of zinc phosphate and the drawing media occurs, which results in an optimal performance regarding degree and rate of deformation
• Can be used in very low concentrations of 5 - 10% as an aqueous solution (tube drawing). The best results are obtained with water free media
• Offers (in combination with a zinc phosphate layer) very high cross-sectional reduction and high drawing velocities – up to 100 m/min (steel tubes with standard cross-sectional reduction)

WEDOLiT FW 1970-40K is an extremely high-viscosity, water-soluble lubricant suitable for the drawing of bright steel tubes and bars. The undiluted product is usually applied using brushes or felt rollers.

• Stable load-bearing capacity and homogeneous sliding properties
• Reliably reduces friction and wear, thereby contributing to long tool life
• Excellent wetting and film formation without sticking
• Stable cold start behaviour; prevents stick-slip and chattering
• Results in clean surfaces and contributes to dimensional accuracy
• Can be removed with aqueous cleaners

WEDOLiT FW 3500 is a high-pressure agent for hydroforming-processes such as internal and external high pressure forming of steel plates, with different surface qualities and thicknesses. The product can also be applied in different grinding and cooling operations.

Approved by “FF Fluid Forming“

• Offers very good high-pressure properties
• Contributes to a high tool life
• Very good application stability
• Almost free of foam
• Offers very good skin compatibility


Recommended mixing ratio
• Hydrofroming:  from 5 - 10%
• Grinding:  from 3 - 6%

WEDOLiT FW 6550-165 is a synthetic, mineral oil and chlorine-free, highly additivated punching and forming medium. The EP additives ensure a pressure-resistant lubricating film, even in difficult machining processes.

• Suitable for deep-drawing, extrusion, punching and cutting processes not only on steels, but also on stainless steels
• Undiluted by brush or felt roller and can be easily washed off with water
• Does not contain any insoluble pigments such as graphite or molybdenum disulfide

WEDOLiT C 142 is primarily used for manufacturing steel pipes on pipe welding machines and as a press water additive, and is also suitable for galvanized materials.

• The requirements for cleanliness of the rollers and pipes are met
• Due to its temperature stability, it can also be used in the water cooling section for the weld seam, in addition to cooling the electrode or for high-frequency welding of coils and impeders
• The entire pipe welding machine is thus operated with a closed cooling lubrication system without external water supply
• Has no emulsifying effect on mineral oils and machine lubricants
• This makes it possible to use rust protection oil on the turret head of pipe welding machines in the manufacture of profile pipes
• Metal abrasion can be easily removed without clogging the filters. Foreign oils introduced as leak oil can be centrifuged without loss of active ingredients
• Can be easily removed with organic solvents and alkaline cleaners

WEDOLiT FW 7641 is preferably used for the production of steel tubes on tube welding machines and as a press water additive and is also suitable for galvanised materials.

• It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers
• Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
• No emulsification of mineral oils and engine lubricants, therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
• Metal abrasion can be removed easily and without clogging the filters
• Tramp oils introduced as leakage oil can be centrifuged without loss of active substances
• Can be easily removed with organic solvents and alkaline cleaners

WEDOLiT FW 7650 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

• Due to its thermal stability the product can be used in the whole production line (forming, welding, calibration, sawing)
• No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing

WEDOLiT FW 7651 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

• Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
• No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing


Recommended mixing ratio
• Tube welding:  from 4 - 6%

WEDOLiT FW 7652 is suitable for wire drawing as well as for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

• Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
• No emulsification of mineral oils and engine lubricants. Therefore, the application of a corrosion inhibition oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing


Recommended mixing ratio
• Tube welding:  from 4 - 6%
• Wire drawing:  from 3 - 12%

WEDOLiT FW 7661 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 3 - 5%).

• Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
• No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacturing of profiled tubes)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing


Recommended mixing ratio
• Tube welding:  3 -5%

WEDOLiT FW 7840 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration from 7%).

The product is approved by Mercedes-Benz Group AG (formerly Daimler AG) (QSO 040305) under the name WEDOLiT K 911.

• Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing


Recommended mixing ratio
• Tube welding:  from 7%

WEDOLiT FW 9114 is a water miscible forming lubricant based on biodegradable natural raw materials. The product is universally applicable in steel forming processes.

The application concentration depends on the level of difficulty of the forming operations and has to be determined in preliminary tests. Concentrations of 10 - 30% are usually recommended.

• Can be applied undiluted as a concentrate
• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Very good material compatibility
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT FW 9200 is an ester-based, water-miscible forming lubricant, which can be universally applied in forming (especially drawing) processes of brass and non-ferrous metals.

The application concentration depends on the level of difficulty of the forming operations and has to be determined in preliminary tests. Concentrations of 10 - 15% are usually recommended.

• Can be applied undiluted as a concentrate
• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• Very good material compatibility
• Easily removable with organic solvents or alkaline industrial cleaners


Recommended mixing ratio
• Drawing operations:  10 - 15%

WEDOLiT FW 9900 is a water-miscible, ester based forming lubricant (soap) that can be used universally for deep drawing and other forming operations of brass. The concentration depends on the level of difficulty of the forming operation and should be determined in preliminary tests (usually in the range between 10 - 15%). The product can also be used undiluted.

• Outstanding performance
• Stable load carrying capacity and a homogenous sliding behaviour
• Reduces friction and wear and thus contributes to a high tool life
• Outstanding wetting ability and film formation without adhesion
• Stable cold start behaviour, prevents stick-slip and chatter
• Leads to clean surfaces and contributes to achieve dimensional accuracy
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT K 102 is a mildly alkaline, sprayable, mineral oil containing corrosion protection emulsion, free of boron compounds and formaldehyde releasers, suitable for temporary corrosion protection of workpieces made of steel, ferrous and non-ferrous materials.
Approved by Rattunde & Co

• The product forms a stable emulsion, regardless of the concentration
• Due to the electrolyte and temperature stability, an application in a heated bath is possible (recommended temperature 60 - 80°C)
• Even at high temperatures the product is stable against contaminations (e.g. sodium sulfonates or phosphates)
• Easily removable with solvents or alkaline industrial cleaners
• For corrosion protection it´s important that treated parts are completely dry before packaging
• Depending on the concentration, a slightly noticeable film is formed on the metal surface
• Very good compatibility with VCI foils
• Outstanding material compatibility (even at higher concentration)

WEDOLiT K 119 is a modern formulated corrosion inhibitor for steel and other metals. It offers protection for a short storage period and is suitable for light straightening processes. It can be applied by spraying, flooding or by means of rollers.

Approved by Porsche under PTL 6701-2001-06.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31. BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

• Suitable for VCI-foils
• Stable against acidic and alkaline contamination
• Good material compatibility
• Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

WEDOLiT K 856 is a dewatering fluid with slight corrosion protection properties that uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can be dewatered efficiently. It is mainly used as an immersion bath at room temperature.

Fulfils all requirements regarding Altautorichtlinie 2000/53/EG. Not subject to the German VOC-regulation (VOC-guideline, 31 BImSchV) or to the Swiss regulation for VOC (Lenkungsabgabe VOCV Swiss).

• Due to its strong dewatering effect, residues of flushing water or water containing fluids such as emulsions or synthetic coolants are removed from the metal surface
• Water/emulsions that enter the bath will settle on the bottom of the tank after a short period and can be drained off
• Development of a clear phase boundary between the water and the product, without forming an emulsion phase
• Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils
• Excellent bath-life
• Additive loss due to water contact: None

WEDLiT N 22-3 is a thixotropic, non water soluble, deep drawing agent, which was developed for cold forming of coated carbon steels. It is especially applicable for electro galvanised zinc-, zinc nickel coated- and aluminised-sheets. Also good for aluminium and aluminium alloys. The product can be applied by spraying, flooding or rolling.

Fulfils the requirements of all German automotive manufacturers according to VDA-213 and VW-A001, and has been approved by all VDA members.

• Applications at ambient temperatures possible
• A preheating of the oil to approximately 40 - 50°C is possible without the loss of the thixotropic effect after cooling
• Acts at the same time as a corrosion protection agent, and therefore a post treatment of the drawn sheets is not necessary
• An agent stable film is formed after drawing
• Can be removed with organic solvents or water soluble, mild alkaline industrial cleaning agents, even after long storage periods
• After grease removal, excellent phosphating is possible

WEDOLiT N 22-4 is a medium-viscosity, non-water-soluble forming oil for deep-drawing operations of sheet steel, for example, for the automotive industry. This includes sheet metal that is galvanized, or hot-dip galvanized on one or both sides, sheet metal coated with zinc metal, aluminized sheet metal, or sheets made of aluminum or aluminum alloys.

The product meets the requirements of the test procedure according to VDA 230-213, and has been approved by all VDA members.

• Also acts as an anti-corrosion oil
• Subsequent preservation of drawn parts is not necessary due to the good corrosion protection
• Can be applied by spraying, flooding, brushing or with felt rollers
• The oil film can be easily removed with organic solvents or water-soluble alkaline cleaners

WEDOLiT N 22 NV is a thixotropic water insoluble washing oil for cleaning metal sheets and coils. The product is usually used in washing machines at ambient temperatures. Increasing the temperature to approx. 60 °C enhances the washing effect. The oil film that remains on the surface after the washing process offers sufficient forming properties for medium to heavy forming operations (for cold forming of uncoated and galvanized steel and for and aluminum).

Approved by Volkswagen (VW-Material-Nr. 29.4186) and by Mercedes Benz (Nr. 34/95-10576 VWT).

• Compatible (according to tests and our experience) with all for the automotive industry typical adhesives and paints (KTL)
• Acts as a corrosion protection agent. Therefore, a post-treatment of the drawn sheets is not necessary
• An ageing stable film is formed after drawing
• Can easily be removed with organic solvents or water soluble, mild industrial alkaline cleaning agents, even after long storage periods
• A phosphating can easily be conducted after degreasing

WEDOLiT N 52 is a mineral-oil based high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems such as milling, sawing or thread forming steel, aluminium and non-ferrous metals*.
Approved by Rattunde & Co as a cutting oil for minimum quantity lubrication.

• Stable load carrying capacity and a homogenous sliding behaviour
• Very good wetting ability and film formation without adhesion
• Outstanding cooling and lubrication properties lead to significantly reduced friction and wear and thus contribute to long tool life
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• Economical application
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT SA 1 is a splitting agent that is used to reduce the pH value of an emulsion and start the demulsification process. The optimal pH value has to be determined in preliminary tests.

• Applicable at ambient temperature
• The suitability and the required volume, which depends on the concentration of the expander oil, have to be determined in preliminary tests (laboratory scale)
• To ensure a thorough mixing the product should be added at points with high circulation

WEDOLiT SA 2 is used to neutralize the pH value of an emulsion that was treated with a splitting agent. The optimal pH value has to be determined in preliminary tests.

• Applicable at ambient temperature
• The suitability and the required volume, which depends on the concentration of the expander oil, have to be determined in preliminary tests (laboratory scale)
• To ensure a thorough mixing the product should be added at points with high circulation

WEDOLiT SA 3 is used for the demulsification process of used emulsions and serves as a flocculant for industrial waste-water.

• Applicable at ambient temperature
• The suitability and the required volume, which depends on the concentration of the expander oil, have to be determined in preliminary tests (laboratory scale)
• The required volume is usually in the range of 1 - 20 g/m³
• To ensure a thorough mixing the product should be added at points with high circulation