WEDOLiT CS 6206 is suitable for grinding of steel, cast iron, aluminium, non-ferrous metals, glass and especially carbides.

• Offers high cooling- and flushing properties with a very good wetting behaviour
• Contributes to a high tool life
• Very good application stability
• Almost free of foam
• Offers a good skin compatibility


Recommended mixing ratio
• Grinding:  from 4%
• General cutting:  from 6%

WEDOLiT CW 6506 is suitable for light to heavy cutting operations of steel, stainless steel, aluminium (e.g. sensitive aluminium alloys of the 2000 and 7000 series), titanium and non-ferrous metals*.

WEDOLiT CW 6506 is approved by CETIM according to specification EADS ASN 42302 annex 2, DASSAULT DQGT 0.4.2.0065 index D and by Bombardier BAMS 569-001 rev. B, for the aerospace industry.

• Offers high cooling- and flushing properties with a very good wetting behaviour
• Contributes to a high tool life
• Very good application stability
• Almost free of foam
• Offers a very good skin compatibility

WEDOLiT EP 1090-E is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilisation in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents the stick-slip- effect due to the high content of polar additives.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 435 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 540 ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and due to the high content of polar additives, prevents the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and expander heads and can be easily separated into water and oily waste by utilising specific additives
• Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 760 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilisation in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilisation of specific additives
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT EP 760 ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilisation in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and due to the high content of polar additives, prevents the stick-slip-effect.

• Very high film stability (even under high pressures)
• Good adhesion properties on smooth surfaces, very good wear protection
• Easily removable with water (spontaneous emulsification)
• The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by utilising specific additives
• Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed
• The treated water can be reused for the preparation of a new emulsion (to a certain degree)

WEDOLiT FW 1960 is a water-soluble alkaline soap for heavy drawing operations of steel tubes. The product is usually used as an immersion bath (bath temperature 75 – 90°C).

• The product is designed to react with the zinc phosphate layer (which acts as lubricant) to form a zinc soap. The zinc phosphate layer should be at least 4 μm (at heavy forming operations, e.g. cold extrusion, up to 10 μm). Due to specific additives, a maximum conversion of zinc phosphate and the drawing media occurs, which results in an optimal performance regarding degree and rate of deformation
• Can be used in very low concentrations of 5 - 10% as an aqueous solution (tube drawing). The best results are obtained with water free media
• Offers (in combination with a zinc phosphate layer) very high cross-sectional reduction and high drawing velocities – up to 100 m/min (steel tubes with standard cross-sectional reduction)

WEDOLiT FW 3500 is a high-pressure agent for hydroforming-processes such as internal and external high pressure forming of steel plates, with different surface qualities and thicknesses. The product can also be applied in different grinding and cooling operations.

Approved by “FF Fluid Forming“

• Offers very good high-pressure properties
• Contributes to a high tool life
• Very good application stability
• Almost free of foam
• Offers very good skin compatibility


Recommended mixing ratio
• Hydrofroming:  from 5 - 10%
• Grinding:  from 3 - 6%

WEDOLiT FW 7651 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

• Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
• No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing


Recommended mixing ratio
• Tube welding:  from 4 - 6%

WEDOLiT FW 7652 is suitable for wire drawing as well as for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

• Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
• No emulsification of mineral oils and engine lubricants. Therefore, the application of a corrosion inhibition oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing


Recommended mixing ratio
• Tube welding:  from 4 - 6%
• Wire drawing:  from 3 - 12%

WEDOLiT FW 7661 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 3 - 5%).

• Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
• No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacturing of profiled tubes)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing


Recommended mixing ratio
• Tube welding:  3 -5%

WEDOLiT FW 7840 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration from 7%).

The product is approved by Mercedes-Benz Group AG (formerly Daimler AG) (QSO 040305) under the name WEDOLiT K 911.

• Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)
• Can be centrifuged without loss of active substances
• Removable with organic solvents or alkaline industrial cleaners
• A bright workpiece surface is obtained after annealing


Recommended mixing ratio
• Tube welding:  from 7%