Leading Solutions for Tubes
Outstanding dewatering fluids
Very fast dewatering, offers short-term corrosion protection, lower flash point
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Bright yellow, clear |
Visual |
Density at 15°C: |
0.79 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
2.2 mm2/s |
ASTM D 7042 |
Flash point: |
> 40 °C |
DIN EN ISO 2719 |
Film weight: |
0.3 g/m2 |
Dipping procedure |
Film type: |
Very slightly oily |
Haptical |
Dewatering effect: |
≤ 5 s |
Internal test method |
Water separation: |
4 min |
Internal test method |
Humidity test: |
10 cycles |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
< 1 h |
DIN EN ISO 9227 NSS |
Very fast dewatering, offers short-term corrosion protection,
higher flash point
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Bright yellow, clear |
Visual |
Density at 15°C: |
0.80 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
2.8 mm2/s |
ASTM D 7042 |
Flash point: |
> 60 °C |
DIN EN ISO 2719 |
Film weight: |
0.3 g/m2 |
Dipping procedure |
Film type: |
Very slightly oily |
Haptical |
Dewatering effect: |
≤ 5 s |
Internal test method |
Water separation: |
4 min |
Internal test method |
Humidity test: |
7 cycles |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
< 1 h |
DIN EN ISO 9227 NSS |
Very fast dewatering, offers short-term
corrosion protection, VOC free version
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Bright yellow, clear |
Visual |
Density at 15°C: |
0.81 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
4.1 mm2/s |
ASTM D 7042 |
Flash point: |
> 100 °C |
DIN EN ISO 2719 |
Film weight: |
0.3 g/m2 |
Dipping procedure |
Film type: |
Very slightly oily |
Haptical |
Dewatering effect: |
≤ 5 s |
Internal test method |
Water separation: |
4 min |
Internal test method |
Humidity test: |
7 cycles |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
< 1 h |
DIN EN ISO 9227 NSS |
High corrosion protection with dewatering effect
Outstanding universal corrosion protection for
long-term overseas transportation
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Brown, clear |
Visual |
Density at 15°C: |
0.81 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
2.2 mm2/s |
ASTM D 7042 |
Flash point: |
> 40 °C |
DIN EN ISO 2719 |
Film weight: |
1.4 g/m2 |
Dipping procedure |
Film type: |
Oily |
Haptical |
Dewatering effect: |
≤ 30 s |
Internal test method |
Water separation: |
8 min |
Internal test method |
Humidity test: |
150 cycles |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
60 h |
DIN EN ISO 9227 NSS |
Thin film wax corrosion protection, no influence
on subsequent processes, for mid-term storage
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Medium-brown, clear |
Visual |
Density at 15°C: |
0.81 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
2.3 mm2/s |
ASTM D 7042 |
Flash point: |
> 60 °C |
DIN EN ISO 2719 |
Film weight: |
0.5 g/m2 |
Dipping procedure |
Film type: |
Microwax |
Haptical |
Dewatering effect: |
≤ 30 s |
Internal test method |
Water separation: |
4 min |
Internal test method |
Humidity test: |
90 cycles |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
24 h |
DIN EN ISO 9227 NSS |
Corrosion protection with an outstanding
performance, for overseas long-term
transportation
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Medium-brown, clear |
Visual |
Density at 15°C: |
0.82 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
2.8 mm2/s |
ASTM D 7042 |
Flash point: |
> 60 °C |
DIN EN ISO 2719 |
Film weight: |
1.4 g/m2 |
Dipping procedure |
Film type: |
Oily |
Haptical |
Dewatering effect: |
≤ 30 s |
Internal test method |
Water separation: |
9 min |
Internal test method |
Humidity test: |
120 cycles |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
48 h |
DIN EN ISO 9227 NSS |
VOC free for short-term corrosion protection
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Yellow-medium-brown, clear |
Visual |
Density at 15°C: |
0.86 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
13.8 mm2/s |
ASTM D 7042 |
Flash point: |
> 120 °C |
DIN EN ISO 2719 |
Film weight: |
1.5 g/m2 |
Dipping procedure |
Film type: |
Oily |
Haptical |
Dewatering effect: |
≤ 30 s |
Internal test method |
Water separation: |
17 min |
Internal test method |
Humidity test: |
50 cycles |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
2 h |
DIN EN ISO 9227 NSS |
High corrosion protection, wax dispersion
Thick, waxy high performance product,
potentially for outdoor storage
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Black, cloudy |
Visual |
Density at 15°C: |
0.81 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
74.0 mm2/s |
ASTM D 7042 |
Flash point: |
> 38 °C |
DIN EN ISO 2719 |
Film weight: |
28.0 g/m2 |
Dipping procedure |
Film type: |
Waxy |
Haptical |
Dewatering effect: |
None |
Internal test method |
Water separation: |
None |
Internal test method |
Humidity test: |
1500 cycles |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
220 h |
DIN EN ISO 9227 NSS |
High corrosion protection, straightening oils
Ideal for short-term corrosion protection of
dry workpieces, suitable for light forming
operations, VOC free
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Brown, clear |
Visual |
Density at 15°C: |
0.85 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
10.5 mm2/s |
ASTM D 7042 |
Flash point: |
> 100 °C |
DIN EN ISO 2719 |
Film weight: |
1.2 g/m2 |
Dipping procedure |
Film type: |
Oily |
Haptical |
Dewatering effect: |
None |
Internal test method |
Water separation: |
18 min |
Internal test method |
Humidity test: |
60 cycles |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
24 h |
DIN EN ISO 9227 NSS |
Specialist fluids for special applications
Multi-purpose oil, with forming properties, also
available in aerosol cans (WEDOLiT KS 3000)
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Medium-brown, clear |
Visual |
Density at 15°C: |
0.83 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
4.4 mm2/s |
ASTM D 7042 |
Flash point: |
> 60 °C |
DIN EN ISO 2719 |
Film weight: |
1.8 g/m2 |
Dipping procedure |
Film type: |
Oily |
Haptical |
Dewatering effect: |
≤ 60 s |
Internal test method |
Water separation: |
5 min |
Internal test method |
Humidity test: |
70 cycles |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
8 h |
DIN EN ISO 9227 NSS |
New generation ester-based corrosion protection
Ester-based dewatering fluid, no negative labelling, mineral oil free
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Light yellow, clear |
Visual |
Density at 15°C: |
0.86 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
11.2 mm2/s |
ASTM D 7042 |
Flash point: |
> 160 °C |
DIN EN ISO 2719 |
Film weight: |
0.5 g/m2 |
Dipping procedure |
Film type: |
Slightly oily |
Haptical |
Dewatering effect: |
≤ 30 s |
Internal test method |
Water separation: |
12 min |
Internal test method |
Humidity test: |
14 cycles |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
< 1 h |
DIN EN ISO 9227 NSS |
Ester-based corrrosion protection, no negative labelling, mineral
oil free
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Yellow, clear |
Visual |
Density at 15°C: |
0.95 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
63.6 mm2/s |
ASTM D 7042 |
Flash point: |
> 160 °C |
DIN EN ISO 2719 |
Film weight: |
0.8 g/m2 |
Dipping procedure |
Film type: |
Slightly oily |
Haptical |
Dewatering effect: |
None |
Internal test method |
Water separation: |
None |
Internal test method |
Humidity test: |
30 cycles |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
8 h |
DIN EN ISO 9227 NSS |
Water-miscible corrosion protection
Water-miscible parts cleaner, very good corrosion
protection, application at approximately 60°C,
for steel and non-ferrous metals
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Dark brown, clear-slightly turbid |
Visual |
Density at 15°C: |
0.91 g/cm3 |
ASTM D 7042 |
Viscosity at 40°C: |
44.0 mm2/s |
ASTM D 7042 |
Flash point: |
> 100 °C |
DIN EN ISO 2719 |
pH-value [20%; 70°C]: |
9.8 |
DIN EN ISO 10523 |
Conductivity [20%; 70°C]: |
1850 µS/cm |
DIN EN 27888 |
Corrosion protection properties
Concentration: |
10% |
20% |
100% |
Tested according to |
Film weight: |
1.8 g/m2 |
4.7 g/m2 |
5.2 g/m2 |
Dipping procedure |
Humidity test: |
> 1 d |
> 2 d |
> 4 d |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
< 2 h |
< 16 h |
> 24 h |
DIN EN ISO 9227 NSS |
Water-miscible parts cleaner, application at
approximately 60°C, for steel and non-ferrous
metals, Rattunde approval
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Dark brown, clear-slightly turbid |
Visual |
Density at 15°C: |
0.97 g/cm3 |
ASTM D 7042 |
Viscosity at 40°C: |
108.0 mm2/s |
ASTM D 7042 |
Flash point: |
> 100 °C |
DIN EN ISO 2719 |
pH-value [20%; 70°C]: |
8.5 |
DIN EN ISO 10523 |
Conductivity [20%; 70°C]: |
4500 µS/cm |
DIN EN 27888 |
Corrosion protection properties
Concentration: |
10% |
20% |
100% |
Tested according to |
Film weight: |
0.8 g/m2 |
1.2 g/m2 |
5.2 g/m2 |
Dipping procedure |
Humidity test: |
> 1 d |
> 2 d |
> 4 d |
DIN EN ISO 6270-2 AHT |
Salt spray performance: |
< 1 h |
< 1 h |
> 1 h |
DIN EN ISO 9227 NSS |
Tube welding solutions / Emulsions
Fully synthetic tube welding medium for bright steel
Physical Properties Typical Data
Concentrate |
Colour |
Mineral oil content |
Viscosity at 20°C: ASTM D 7042 |
Density at 20°C: ASTM D 7042 |
Copper corrosion: DIN 51759-1 |
Yellow, clear |
Free |
6.6 mm2/s |
1.06 |
Not determined* |
5% Solution |
Colour |
pH-value (tap water) |
Corrosion protection DIN 51360-2 |
Refractometer factor (brix) |
Conductivity (Deionised water) |
Clear |
9.4 |
5 % grade 0 |
2.3 |
1940 μS/cm |
Characteristics
Mineral oil |
EP-additives |
Chlorine |
Boron |
Amines |
FAD |
- |
+ |
- |
+ |
+ |
+ |
*Discolourations of non-ferrous metals should be examined in preliminary tests
For welding of galvanised steel tubes, mineral oil free
Physical Properties Typical Data
Concentrate |
Colour |
Mineral oil content |
Viscosity at 20°C: ASTM D 7042 |
Density at 20°C: ASTM D 7042 |
Copper corrosion: DIN 51759-1 |
Yellow, clear |
Free |
6.1 mm2/s |
1.08 |
Not determined* |
5% Solution |
Colour |
pH-value (tap water) |
Corrosion protection DIN 51360-2 |
Refractometer factor (brix) |
Conductivity (Deionised water) |
Clear |
9.5 |
5 % grade 0 |
2.3 |
3090 μS/cm |
Characteristics
Mineral oil |
EP-additives |
Chlorine |
Boron |
Amines |
FAD |
- |
- |
- |
+ |
+ |
+ |
*Discolourations of non-ferrous metals should be examined in preliminary tests
Fully synthetic tube welding medium for bright steel,
boron free version of FW 7651
Physical Properties Typical Data
Concentrate |
Colour |
Mineral oil content |
Viscosity at 20°C: ASTM D 7042 |
Density at 20°C: ASTM D 7042 |
Copper corrosion: DIN 51759-1 |
Yellow, clear |
Free |
8.0 mm2/s |
1.06 |
Not determined* |
5% Solution |
Colour |
pH-value (tap water) |
Corrosion protection DIN 51360-2 |
Refractometer factor (brix) |
Conductivity (Deionised water) |
Clear |
9.4 |
5 % grade 0 |
2.3 |
1590 μS/cm |
Characteristics
Mineral oil |
EP-additives |
Chlorine |
Boron |
Amines |
FAD |
- |
+ |
- |
- |
+ |
+ |
*Discolourations of non-ferrous metals should be examined in preliminary tests
Tube welding emulsion for bright and galvanised steel
Physical Properties Typical Data
Concentrate |
Colour |
Mineral oil content |
Viscosity at 20°C: ASTM D 7042 |
Density at 20°C: ASTM D 7042 |
Copper corrosion: DIN 51759-1 |
Brown |
30 % |
186.0 mm2/s |
0.98 |
Not determined* |
5% Solution |
Colour |
pH-value (tap water) |
Corrosion protection DIN 51360-2 |
Refractometer factor (brix) |
Conductivity (Deionised water) |
Whitish |
9.2 |
5 % grade 0 |
1.0 |
1550 μS/cm |
Characteristics
Mineral oil |
EP-additives |
Chlorine |
Boron |
Amines |
FAD |
+ |
- |
- |
- |
- |
+ |
*Discolourations of non-ferrous metals should be examined in preliminary tests
Tube and wire manufacturing
High performance oil for drawing of steel and stainless
steel wires, contains chlorine
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Yellow |
Visual |
Density at 20°C: |
1.45 g/cm3 |
ASTM D 7042 |
Viscosity at 40°C: |
2335.0 mm2/s |
ASTM D 7042 |
Flash point: |
> 190 °C |
DIN EN ISO 2719 |
Copper corrosion: |
Not determined* |
DIN 51759-1 |
*Discolourations of non-ferrous metals should be examined in preliminary tests
For copper and copper-iron alloys
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Clear |
Visual |
Density at 20°C: |
0.90 g/cm3 |
ASTM D 7042 |
Viscosity at 40°C: |
2780.0 mm2/s |
ASTM D 7042 |
Flash point: |
> 160 °C |
DIN EN ISO 2719 |
Copper corrosion: |
1a |
DIN 51759-1 |
Chlorine free pilger paste for stainless steel tubes
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Beige |
Visual |
Density at 20°C: |
1.20 g/cm3 |
ASTM D 7042 |
Viscosity at 40°C: |
Not measurable |
ASTM D 7042 |
Flash point: |
> 100 °C |
DIN EN ISO 2719 |
Copper corrosion: |
Not determined* |
DIN 51759-1 |
*Discolourations of non-ferrous metals should be examined in preliminary tests
For drawing of tubes with small diameters (e.g. for diesel
injection lines)
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Brown, clear |
Visual |
Density at 20°C: |
0.90 g/cm3 |
ASTM D 7042 |
Viscosity at 40°C: |
90.0 mm2/s |
ASTM D 7042 |
Flash point: |
> 220 °C |
DIN EN ISO 2719 |
Copper corrosion: |
1b |
DIN 51759-1 |
Evaporating straightening and polishing oil for aluminum and
brass tubes, quickly evaporates without leaving any residue
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Transparent |
Visual |
Density at 20°C: |
0.76 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
1.8 mm2/s |
ASTM D 7042 |
Flash point: |
> 56 °C |
DIN EN ISO 2719 |
Copper corrosion: |
Not determined* |
DIN 51759-1 |
*Discolourations of non-ferrous metals should be examined in preliminary tests
Evaporating forming oil e.g. for coiling steel tubes for heat
exchangers
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Yellow brown |
Visual |
Density at 20°C: |
0.84 g/cm3 |
ASTM D 7042 |
Viscosity at 20°C: |
7.4 mm2/s |
ASTM D 7042 |
Flash point: |
> 61 °C |
DIN EN ISO 2719 |
Copper corrosion: |
Not determined* |
DIN 51759-1 |
*Discolourations of non-ferrous metals should be examined in preliminary tests
Drawing soap, for steel and galvanized steel, application at
approximately 50°C
Physical Properties Typical Data
Parameter |
Typical results |
Operating concentration |
5 - 10 % |
Operating temperature |
75 - 90 °C |
Retention time in soap bath |
5 - 10 min |
Drawing velocity |
Max. 100 m/min |
Concentration (grease in piston) |
6 - 7 % grease |
Concentration (alkalinity in methanol) |
0 - 2 ml |
High performance oil for sawing tubes, Rattunde approval
Physical Properties Typical Data
Parameter |
Typical results |
Tested according to |
Appearance: |
Medium brown, clear |
Visual |
Density at 20°C: |
0.91 g/cm3 |
ASTM D 7042 |
Viscosity at 40°C: |
120.0 mm2/s |
ASTM D 7042 |
Flash point: |
> 180 °C |
DIN EN ISO 2719 |
Copper corrosion: |
Not determined* |
DIN 51759-1 |
*Discolourations of non-ferrous metals should be examined in preliminary tests
Testing media for leakage and ultrasonic tests
Fully synthetic product for ultrasonic tests, very good corrosion protection and ideal
foaming behaviour
Physical Properties Typical Data
Concentrate |
Colour |
Mineral oil content |
Viscosity at 20°C: ASTM D 7042 |
Density at 20°C: ASTM D 7042 |
Copper corrosion: DIN 51759-1 |
Yellow |
Free |
9.0 mm2/s |
1.10 |
Not determined* |
5% Solution |
Colour |
pH-value (tap water) |
Corrosion protection DIN 51360-2 |
Refractometer factor (brix) |
Conductivity (Deionised water) |
Transparent |
9.4 |
5 % grade 0 |
1.9 |
2270 μS/cm |
Characteristics
Mineral oil |
EP-additives |
Chlorine |
Boron |
Amines |
FAD |
- |
- |
- |
+ |
+ |
+ |
*Discolourations of non-ferrous metals should be examined in preliminary tests
Fully synthetic product with very good material
compatibility, water-miscible
Physical Properties Typical Data
Concentrate |
Colour |
Mineral oil content |
Viscosity at 20°C: ASTM D 7042 |
Density at 20°C: ASTM D 7042 |
Copper corrosion: DIN 51759-1 |
Yellow |
Free |
4.7 mm2/s |
1.05 |
Not determined* |
5% Solution |
Colour |
pH-value (tap water) |
Corrosion protection DIN 51360-2 |
Refractometer factor (brix) |
Conductivity (Deionised water) |
Yellowish |
9.6 |
5 % grade 0 |
2.2 |
Not determined |
Characteristics
Mineral oil |
EP-additives |
Chlorine |
Boron |
Amines |
FAD |
- |
- |
- |
+ |
+ |
+ |
*Discolourations of non-ferrous metals should be examined in preliminary tests