WEDOLiT CN 5370-12 is a low viscous, non-water soluble high performance cutting oil based on the latest GTL-baseoil-technology, which was developed for thread cutting operations. The product is also suitable for general cutting operations of high alloyed steels, cast iron, aluminium and non-ferrous metals.

• High performance product, which leads to an excellent surface finish and dimensional accuracy
• Special additivation for thread cutting operations
• Highly reduced oil mist formation, almost no loss of evaporation
• Reduces friction and wear and thus contributes to a high tool life
• Offers high cooling properties with a very good wetting behaviour
• Very good flushing behaviour with an optimal transport of chips and swarf
• Easily removable with organic solvents or alkaline industrial cleaners

WEDOLiT CN 6850-26 is a medium viscous high-performance oil for machining steel, stainless steel, cast iron, aluminium and non-ferrous metals. By using this oil, various processes can be avoided such as separate production lines for machining different materials and the preliminary cleaning of non-ferrous metals. The product can be applied undiluted by spraying, flooding or means of rollers.

• High performance product, which leads to an excellent surface finish and dimensional accuracy
• Highly reduced oil mist formation, almost no loss of evaporation
• Reduces friction and wear and thus contributes to a high tool life
• Offers high cooling properties with a very good wetting behaviour
• Very good flushing behaviour for an optimal transport of chips and swarf
• Easily removable with organic solvents or alkaline industrial cleaners
• A higher or lower viscosity can be created (equal additive content) by variation of the base oil

WEDOLiT CS 6206 is suitable for grinding of steel, cast iron, aluminium, non-ferrous metals, glass and especially carbides.

• Offers high cooling- and flushing properties with a very good wetting behaviour
• Contributes to a high tool life
• Very good application stability
• Almost free of foam
• Offers a good skin compatibility


Recommended mixing ratio
• Grinding:  from 4%
• General cutting:  from 6%

WEDOLiT CW 6506 is suitable for light to heavy cutting operations of steel, stainless steel, aluminium (e.g. sensitive aluminium alloys of the 2000 and 7000 series), titanium and non-ferrous metals*.

WEDOLiT CW 6506 is approved by CETIM according to specification EADS ASN 42302 annex 2, DASSAULT DQGT 0.4.2.0065 index D and by Bombardier BAMS 569-001 rev. B, for the aerospace industry.

• Offers high cooling- and flushing properties with a very good wetting behaviour
• Contributes to a high tool life
• Very good application stability
• Almost free of foam
• Offers a very good skin compatibility

WEDOLiT FS 3910 is non-water-soluble cooling lubricant with low viscosity for punching- and bending operations on steel and zinc coated steel. The product is not applicable for the treatment of nonferrous metals.

• Can be applied undiluted by spraying, flooding, brushing or rolling
• Has a good spread effect, which causes an optimal even wettability of metal surfaces
• Has a simultaneously cleaning effect
• Contains a combination of aromatic free solvents with additives of esters and extreme-pressure compounds and is therefore practically odourless
• Is marked by a very fast evaporation with high flash point

WEDOLiT FW 6550-165 is a synthetic, mineral oil and chlorine-free, highly additivated punching and forming medium. The EP additives ensure a pressure-resistant lubricating film, even in difficult machining processes.

• Suitable for deep-drawing, extrusion, punching and cutting processes not only on steels, but also on stainless steels
• Undiluted by brush or felt roller and can be easily washed off with water
• Does not contain any insoluble pigments such as graphite or molybdenum disulfide

WEDOLiT N 52 is a mineral-oil based high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems such as milling, sawing or thread forming steel, aluminium and non-ferrous metals*.
Approved by Rattunde & Co as a cutting oil for minimum quantity lubrication.

• Stable load carrying capacity and a homogenous sliding behaviour
• Very good wetting ability and film formation without adhesion
• Outstanding cooling and lubrication properties lead to significantly reduced friction and wear and thus contribute to long tool life
• Leads to clean surfaces and contributes to achieving dimensional accuracy
• Economical application
• Easily removable with organic solvents or alkaline industrial cleaners