Dewatering-fluid 104°F (40°C) flash point

WEDOLiT AS 1012 is a dewatering fluid with corrosion protection properties. It uses surface-active substances to displace both water and emulsions from the metal surface extremely quick. Even highly complex geometries can efficiently be dewatered. It is mainly used as an immersion bath at room temperature.

Due to its strong dewatering effect, residues of flushing water or water containing fluids including emulsions or synthetic coolants are removed from the metal surface

After evaporation of the solvent, a thin, non-adhesive protective film remains on the surface, which offers corrosion protection for short-term intermediate storage

Water/emulsions that enter the bath will settle after a short period on the bottom of the tank and can be drained off

Development of a clear phase boundary between the water and the product, without forming an emulsion phase

Due to its extreme dewatering properties, the product is ideal for workpieces that are additionally packaged with VCI foils

Excellent bath-life

Additive loss due to water contact: None

Long term DW Fluid 104°F (40°C) flash point

WEDOLiT AS-2251 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing or rolling.

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

Stable against acidic and alkaline contamination

Good material compatibility

Water displacing with very good wetting behavior

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Additive loss due to water contact: Very low

High-Protection-Waxdispersion-Fluid 104°F (40°C) flash point

WEDOLiT AS 2603 is a universal, solvent-containing, long-term corrosion protection. It contains a newly formulated thixotropic wax dispersion, which allows a long period of protection under covered storage as well as a limited storage period for outdoor storage. It can be applied by spraying, flooding, brushing or rolling.

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

After the evaporation of the solvent (quick drying time), a waxy, light-coloured, non-adhesive and non-dust-binding, age-resistant protective film is formed on the treated surface

Good protection for outdoor storage

It´s recommended to homogenise the product before use or after a longer storage period

Protection against atmospheric contaminations such as dissolved gases that cannot penetrate the protective film (water vapour permeability)

High-Protection-DW-Fluid 140°F (60°C) flash point, thin film

WEDOLiT AS-4116 is a leading edge corrosion inhibitor for steel and other metals, which offers long-term protection for indoor storage. Its low viscosity allows it to be used as an immersion bath, e.g. for the treatment of hollow parts. It can also be applied by spraying, flooding, brushing of rolling.

Ideal for overseas transport

Suitable for VCI-foils: The full corrosion protection is only given in the solvent-free film, therefore a short storage time until the solvent evaporates must be observed especially before packing in boxes with foils

Stable against acidic and alkaline contamination

Good material compatibility

Water displacing with very good wetting behavior

Easily removable with organic solvents (cold cleaners) or water-miscible alkaline industrial cleaners

Additive loss due to water contact: Extremely low

Water-miscible High-performance Fluid

WEDOLiT AW 8321 is universally applicable for parts cleaning and corrosion protection. This mineral oil based product is not only suitable for steel, but also for non-ferrous metals. Utilizing the latest technology, AW 8321 offers the possibility for a boron and formaldehyde free application.

The product forms a stable emulsion, regardless of the concentration. Due to the electrolyte and temperature stability, an application in heated baths is possible (recommended temperature 140 - 176°F, (60 - 80°C))

Even at high temperatures the product is stable against contaminations (e.g. sodium sulfonates or phosphates)

Easily removable with solvents or alkaline industrial cleaners

For the corrosion protection it´s important that treated parts are completely dry before packaging. Dependent on the concentration a minimal to slightly noticeable film is formed on the metal surface

Very good compatibility with VCI foils

Outstanding material compatibility (even at higher concentration)

Water-miscible, fully synthetic coolant

WEDOLiT CS 8208 is suitable for ultrasonic testing systems. The product is also suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 5 - 10%). Not suitable for the manufacturing of workpieces made of zinc, aluminum and their alloys.

Offers high cooling- and flushing properties with a very good wetting behavior

Contributes to a high tool life

Very good application stability

Almost free of foam

Offers a good skin compatibility

Due to its thermal stability, the product can be used in almost the whole process chain of welded tubes (forming, welding, calibration, sawing)

High performance expander oil

WEDOLiT EP 1090-E is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents the stick-slip- effect due to the high content of polar additives.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by the utilization of specific additives

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander Oil, Easy-splitting Technology, mineral oil based

WEDOLiT EP 540 ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and due to the high content of polar additives, prevents the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and expander heads and can be easily separated into water and oily waste by utilizing specific additives

Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander oil

WEDOLiT EP 760 E is a highly viscous, high-performance forming oil based on renewable raw materials. The product has been developed to the highest technical standard for the utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and prevents, due to the high content of polar additives, the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be separated into water and oily waste by the utilization of specific additives

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

Expander Oil, Easy-splitting Technology, mineral oil based

WEDOLiT EP 760 ES is a highly viscous, high-performance, mineral-oil-based forming oil. The product has been developed to the highest technical standard for utilization in the pipe industry (e.g. manufacturing of large diameter pipes, for gas and oil pipelines). The product can be used undiluted and due to the high content of polar additives, prevents the stick-slip-effect.

Very high film stability (even under high pressures)

Good adhesion properties on smooth surfaces, very good wear protection

Easily removable with water (spontaneous emulsification)

The emulsion can be used for pre- and post-cleaning of the pipes and the expander head and can be easily separated into water and oily waste by utilizing specific additives

Due to the unique easy-splitting-technology, only a very small amount of the splitting media is needed

The treated water can be reused for the preparation of a new emulsion (to a certain degree)

High-performance forming oil

WEDOLiT FN 1190-2300 is a highly viscous, chlorine containing forming oil for tube drawing and other cold forming operations of stainless steel. The undiluted product is usually applied by brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behavior

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behavior, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieving dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Soluble in chlorinated hydrocarbons

Chlorine free stamping oil

WEDOLiT FN 4455-55 is a low viscous, water-insoluble lubricant for heavy forming operations of steel and non-ferrous metals. A combination of EP additives offers a outstanding performance for precision cutting operations. The undiluted product is usually applied by spraying, dipping, brushing, or rolling.

Stable load carrying capacity and a homogenous sliding behavior

Reduces friction and wear and thus contributes to a long tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behavior, prevents stick-slip and chatter

Leads to clean surfaces and contributes to dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

High performance forming oil

WEDOLiT FN 6160-90 is a water-insoluble, chlorinated lubricant for deep drawing and other cold forming operations, e.g. wire drawing, extrusion, or thread forming of steel and stainless steel. The undiluted product is usually applied by flooding, spraying, brushes, or by means of rollers.

Stable load carrying capacity and a homogenous sliding behavior

Reduces friction and wear and thus contributes to a high tool life

Outstanding wetting ability and film formation without adhesion

Stable cold start behavior, prevents stick-slip and chatter

Leads to clean surfaces and contributes to achieve dimensional accuracy

Easily removable with organic solvents or alkaline industrial cleaners

Special forming oil

WEDOLiT FN 8830 is a chlorine free, pasty, water-insoluble lubricant for cold forming processes (e.g. pilgering) of high alloyed steels. The product is usually applied on the outer diameter by brushes or by means of rollers.

Stable load carrying capacity and a homogenous sliding behavior

Reduces friction and wear and thus contributes to a high tool life

The outstanding extreme-pressure properties combined with an exceptional adhesion offers the possibility for high degrees of deformation

Stable cold start behavior, prevents stick-slip and chatter

Contributes to achieving dimensional accuracy

Pigments will remain on the surface after annealing and need to be removed (e.g. by pickling with HCl or HNO₃) before further processing

Straight Cutting and Bending Oil

WEDOLiT FS 3910 is non-water-soluble cooling lubricant with low viscosity for punching- and bending operations on steel and zinc coated steel. The product is not applicable for the treatment of nonferrous metals.

Can be applied undiluted by spraying, flooding, brushing or rolling

Has a good spread effect, which causes an optimal even wettability of metal surfaces

Has a simultaneously cleaning effect

Contains a combination of aromatic free solvents with additives of esters and extreme-pressure compounds and is therefore practically odorless

Is marked by a very fast evaporation with high flash point

Solvent base for aluminum stamping 158°F (70°C)

WEDOLiT FS 4710 is a low viscous, solvent-based lubricant for stamping and forming operations of steel, aluminum and non-ferrous metals. The undiluted product is usually applied by spraying, flooding, brushes, or by means of rollers.

Good spreading behavior, which leads to a uniform wetting of the metal surface

Stable load carrying capacity and a homogenous sliding behavior

Reduces friction and wear and thus contributes to a high tool life

Leads to clean surfaces and contributes to achieving dimensional accuracy

If the product is finely dispersed, it evaporates after a short time without leaving any residue. Therefore, an additional cleaning step is not necessary. Otherwise, it is easily removable with organic solvents or alkaline industrial cleaners

Water-soluble, fully synthetic, good material compatibility

WEDOLiT FW 3500 is a high-pressure agent for hydroforming-processes such as internal and external high pressure forming of steel plates, with different surface qualities and thicknesses. The product can also be applied in different grinding and cooling operations.

Approved by “FF Fluid Forming“

Offers very good high-pressure properties

Contributes to a high tool life

Very good application stability

Almost free of foam

Offers very good skin compatibility

Recommended mixing ratio

Hydrofroming:  from 5 - 10%

Grinding:  from 3 - 6%

Water-miscible, fully synthetic coolant for the whole tube welding line

WEDOLiT FW 7651 is suitable for the manufacturing of welded steel tubes. It fulfills the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 4 - 6%).

Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)

No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacture of profiled tubes)

Can be centrifuged without loss of active substances

Removable with organic solvents or alkaline industrial cleaners

A bright workpiece surface is obtained after annealing

Recommended mixing ratio

Tube welding:  from 4 - 6%

Water-miscible, fully synthetic coolant

WEDOLiT FW 7661 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration of 3 - 5%).

Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)

No emulsification of mineral oils and engine lubricants. Therefore, the application of an anticorrosion oil is possible (e.g. on the Turk’s head of the tube welding engine in the manufacturing of profiled tubes)

Can be centrifuged without loss of active substances

Removable with organic solvents or alkaline industrial cleaners

A bright workpiece surface is obtained after annealing

Recommended mixing ratio

Tube welding:  3 -5%

Emulsion for the whole tube welding line

WEDOLiT FW 7840 is suitable for the manufacturing of welded steel tubes. It fulfils the requirements regarding lubrication and cleanliness of the tubes and rollers as well as the corrosion protection of the tubes and the system (in a concentration from 7%).

The product is approved by Mercedes-Benz Group AG (formerly Daimler AG) (QSO 040305) under the name WEDOLiT K 911.

Due to its thermal stability, the product can be used in the whole production line (forming, welding, calibration, sawing)

Can be centrifuged without loss of active substances

Removable with organic solvents or alkaline industrial cleaners

A bright workpiece surface is obtained after annealing

Recommended mixing ratio

Tube welding:  from 7%

Universal cutting oil

WEDOLiT N 52 is a mineral-oil based high-performance lubricant, suitable for all kinds of minimum quantity lubrication systems such as milling, sawing, or thread forming steel, aluminum, and non-ferrous metals*.
Approved by Rattunde & Co as a cutting oil for minimum quantity lubrication.

Stable load carrying capacity and a homogenous sliding behavior

Very good wetting ability and film formation without adhesion

The outstanding cooling and lubrication properties lead to significantly reduced friction and wear and thus contribute to a long tool life

Leads to clean surfaces and contributes to achieving dimensional accuracy

Economical application

Easily removable with organic solvents or alkaline industrial cleaners