New Products

TRIM™ E950

High Performance Machining Emulsion

TRIM E950 is a proprietary blend of new vegetable-based technology and premium traditional lubricity additives to yield a very high performance, low management metal removal fluid. This premium emulsion product is operator friendly because of its mild contact nature and low chemical initial-charge odour. TRIM E950 is robust enough to deliver extended useful life and avoid rancid odours normally associated with traditional emulsions. The unparalleled lubricity delivers exceptional surface finish and tool life on difficult to machine aluminium alloys, inconel, titanium, stainless and high tensile strength steels.

  • Delivers unparalleled lubricity
  • Very long sump life and low carry-off rates result in low operating cost
  • Low foam even in soft water areas
  • Hard water tolerant
  • Non-chlorinated and non-sulphurised extreme pressure (EP) additives control built-up edge (BUE) in tough operations on aerospace materials
  • Fine emulsion ensures fast wetting to get the fluid to the point of cut and fully coat the work piece and chips for superior tool life and corrosion prevention
  • Compatible with all materials excluding magnesium
  • Easily recycled or disposed of without special handling or equipment
  • Will run effectively for long periods without the need for costly additives

TRIM™ E860

Low-foam, High-lubricity Emulsion

TRIM™ E860 is a high-quality, general purpose emulsion for use on abroad range of ferrous and nonferrous metals, effective in most cutting and grinding operations. The stable and predictable performance of E860 makes it a first choice for precision and consistent parts manufacturing.

  • Very wide application range
  • Good hard water tolerance
  • Keeps machine tools clean
  • Works very well in general machining
  • Very stable formula provides good operational life with consistent performance
  • High tramp oil resistance for easy oil removal and longer coolant life
  • Easily recycled or disposed of using conventional techniques and equipment
  • Good balance of cooling and lubrication providing good tool life and surface finishes
  • Leaves a very light, oily, non-gumming residue to prevent sticky ways, chucks, tool holders, and fixtures
  • Extremely stable fine particle size emulsion allows for reduced carry-off and super-high penetrability to get the fluid to the point of cut

TRIM™ GRIND WC

Carbide Grinding Synthetic

TRIM GRIND WC minimizes cobalt leaching in the grinding of tungsten carbide (WC) and other high cobalt materials. Minimal cobalt leaching means increased piece part integrity, while improving "G RATIOS" and reducing grinding forces. GRIND WC is specifically designed for the carbide grinding industry; it will also perform very well in grinding ceramics, cermets, and tool steels.

  • Keeps super-abrasive wheels clean while not attacking super-abrasive wheel bonding systems
  • Carries grinding swarf to the filter, but will release swarf in properly designed settling tanks
  • Is not stripped out by conventional filtration systems
  • Operators like GRIND WC’s clear working solution for superior visibility while grinding
  • Exceptional sump life and good tramp oil rejection for easy skimming
  • Resists oxidation and varnishing
  • Resists cobalt leaching for improved operator safety, stronger parts, and cleaner machines
  • Very low carryoff equals low fluid makeup costs
  • Easy recycling or disposal with conventional techniques and equipment

TRIM™ SC410

Chlorine-free Semisynthetic Coolant

TRIM SC410 is a chlorine-free, semisynthetic coolant using vegetable-derived and ester lubricants. It runs clean in moderate-duty machining and grinding of both ferrous and nonferrous materials. In addition to its broad range of machining qualities, it has been specially optimized for machining "gray iron" castings and for surface and cylindrical grinding of ferrous materials.

  • Based on our exclusive ester lubricant technology, contains no mineral (petroleum) oil
  • Low foaming in most operations
  • Compatible with a very wide range of materials including ferrous, nonferrous, and nonmetallic material
  • Will provide superior sump life and corrosion inhibition for long periods of time without adds
  • Prevents chip "clinkering" and "hot" chip hoppers when machining cast iron
  • Will keep the machine and work environment clean even when machining or grinding gray iron
  • Contains no chlorine or sulfur-based additives
  • Contains no nitrites, sulfonates, Alkylphenol Ethoxylates, or phenols and is not SARA 313 reportable
  • Very low carryoff and long sump life, delivering low operating costs
  • Hard water tolerant up to 30 grains

TRIM™ MicroSol™ 456

Low-foam Ferrous Semisynthetic

TRIM MicroSol 456 low-foam semisynthetic, microemulsion coolant is optimised for high-volume cast iron, ferrous, and some aluminium and nonferrous metalworking operations. MicroSol 456 prevents leaching of elemental iron and eliminates clinkering and oxidation of ferrous micro fines.

Delivering extended sump life, machine-friendly MicroSol 456 provides excellent, cost-effective cooling. Make a difference to your bottom line with MicroSol 456.

  • Low foaming for today's demanding high-pressure, high-volume applications
  • Also for machining some aluminium alloys and nonferrous metals
  • Provides superior corrosion inhibition on cast iron and eliminates "hot chip" and clinkering problems
  • Keeps machines very clean while leaving a soft fluid film for ease of cleaning and reduced maintenance
  • Requires no special disposal or recycling

TRIM™ DRIVE G2 161C

High-lubricity, Low-foam Semisynthetic

TRIM DRIVE G2 161C is a specialized, halogen-free, high lubricity semisynthetic coolant formulated to meet the high precision machining and stringent chemical restrictions of the Hard Disk Drive (HDD) industry. DRIVE G2 161C has very good wetting and lubricity giving excellent surface finishes. Its ease of wash-ability make DRIVE G2 161C an excellent choice for HDD components manufacturers. DRIVE G2 161C will run in high-pressure situations with little to no foam.

  • Suitable for a wide range of materials including aluminum alloys, steels, and stainless steels
  • Non-staining on aluminum alloys commonly used to produce HDD components
  • Low foam even in high-pressure operations without the use of silicone antifoam
  • Good hydrodynamic lubrication to perform drilling, reaming, and threading applications
  • Excellent anti-weld properties without the use of either chlorinated or sulfurized EP additives
  • Keep machines very clean while leaving a fluid, oily residue for ease of cleaning and reduced machine maintenance costs
  • Does not require special disposal and is easily recycled
  • Parts machined with DRIVE G2 161C can be washed easily and completely in aqueous washing systems